SBS Structural Planter - Revision history

James Klassen: /* WORK INCLUDED */

2025-02-07T18:29:31Z

‎WORK INCLUDED

James Klassen: /* WORK INCLUDED */

2025-02-07T18:26:59Z

‎WORK INCLUDED

James Klassen at 18:21, 27 October 2023

2023-10-27T18:21:56Z

James Klassen: James Klassen moved page SBS 14.3.3 Structures and Equipment (planter pre-curb) to SBS Structural Planter

2022-06-27T18:49:56Z

James Klassen moved page SBS 14.3.3 Structures and Equipment (planter pre-curb) to SBS Structural Planter

James Klassen at 18:49, 27 June 2022

2022-06-27T18:49:41Z

James Klassen at 18:16, 7 September 2021

2021-09-07T18:16:33Z

James Klassen at 21:54, 1 September 2021

2021-09-01T21:54:53Z

James Klassen at 15:59, 30 August 2021

2021-08-30T15:59:34Z

James Klassen at 15:58, 30 August 2021

2021-08-30T15:58:51Z

James Klassen at 14:56, 30 August 2021

2021-08-30T14:56:59Z

@@ Line 28: / Line 28: @@
 ;(5)  [[SBS Roof Systems Standard#PART_14|'''Inside Planter Wall Membrane Flashing''']]: Adhered according to manufacturer's specifications using cold adhesive, self-adhered or torch-applied membrane.  Torching directly to wood surfaces is not permitted. Carry membrane flashing plies to reglet termination near top of planter wall (stagger membrane seal minimum 300mm (6").
 ;(6)  [[SBS Roof Systems Standard#PART_13|'''Reglet - Metal Counter Flashing''']]: As required by the ''RoofStar Guarantee Standards''.  Note that a coping flashing may be paired with the reglet flashing, as illustrated.
-;(7)  '''Plaza Deck / Planter Interior Assembly''': must conform to both the membrane Standard and the RGC Standard for Vegetated Roofs (Note especially [https://rpm.rcabc.org/index.php?title=VRA_Standard#10.1.4.1._General_Requirements_for_Planters Article 10.1.4.1.]).
+;(7)  '''Plaza Deck / Planter Interior Assembly''': Must conform to both the membrane Standard and the RGC Standard for Vegetated Roofs (Note especially [https://rpm.rcabc.org/index.php?title=VRA_Standard#10.1.4.1._General_Requirements_for_Planters Article 10.1.4.1.]).
 <hr>

@@ Line 28: / Line 28: @@
 ;(5)  [[SBS Roof Systems Standard#PART_14|'''Inside Planter Wall Membrane Flashing''']]: Adhered according to manufacturer's specifications using cold adhesive, self-adhered or torch-applied membrane.  Torching directly to wood surfaces is not permitted. Carry membrane flashing plies to reglet termination near top of planter wall (stagger membrane seal minimum 300mm (6").
 ;(6)  [[SBS Roof Systems Standard#PART_13|'''Reglet - Metal Counter Flashing''']]: As required by the ''RoofStar Guarantee Standards''.  Note that a coping flashing may be paired with the reglet flashing, as illustrated.
-;(7)  '''Plaza Deck / Planter Interior Assembly''': Extruded polystyrene insulation and filter mat over primary roof membranes. Concrete pavers placed above pre-curb membrane flashing height, on proprietary pedestals. Note: membrane flashing is not permitted above pre-curb membrane flashing on plaza deck side of planter walls.
+;(7)  '''Plaza Deck / Planter Interior Assembly''': must conform to both the membrane Standard and the RGC Standard for Vegetated Roofs (Note especially [https://rpm.rcabc.org/index.php?title=VRA_Standard#10.1.4.1._General_Requirements_for_Planters Article 10.1.4.1.]).
 <hr>

← Older revision		Revision as of 18:21, 27 October 2023
Line 18:		Line 18:
	</div>		</div>

−	~~::Click below for a printable version of this page.~~
−
−	~~<div style="width:150px; text-align: left;">~~
−	~~:[[File:Pdf.png\|100 px\|link=http://rpm.rcabc.org/images/7/7e/D1.7.6-5_Print_Sheet.pdf\|'''Print Sheet''']]~~
−	~~</div>~~
	</div><!-- COL-MD-6 -->		</div><!-- COL-MD-6 -->

@@ Line 6: / Line 6: @@
 <big><big>Division D - Construction Details</big></big>
 <hr>
-<big><big><big><big><big>SBS 14.3.3 Structures and Equipment (planter pre-curb)</big></big></big></big></big>
+<big><big><big><big><big>SBS | Structural Planter ([[SBS_Roof_Systems_Standard#14.3.2.7._Structures_and_Equipment | Article 14.3.2.7.]])</big></big></big></big></big>
-{| class="wikitable" | style="color: black; background-color: orange; width: 100%;text-align:center"
+{{Template:Construction Details Header}}
 <div class="panel panel-success">
 <div class="panel-heading"><big>'''SBS Details'''</big></div>

@@ Line 1: / Line 1: @@
 {{Template:RPM Info}}
 <hr>
 {| class="wikitable" | style="color: black; background-color: orange; width: 100%;text-align:center"
 | colspan="2"  | <big>'''''Notice to Reader'''''</big>

← Older revision	Revision as of 18:49, 27 June 2022
(No difference)

@@ Line 26: / Line 26: @@
 === WORK INCLUDED ===
 ;(1)  '''Primer''': Application method and coverage rate as approved by Primary Membrane Manufacturer.
-;(2) [[SBS Roof Systems Standard#SBSBASE|'''Primary Roof Membrane''']]: Modified Bituminous base and cap sheet membranes installed as per manufacturer's published application specifications.
+;(2) [[SBS Roof Systems Standard#PART_9|'''Primary Roof Membrane''']]: Modified Bituminous base and cap sheet membranes installed as per manufacturer's published application specifications.
-;(3) [[SBS Roof Systems Standard#SBSPRECURB|'''Pre-Curb (Start-Up Curb) Membrane Flashing''']]: Modified Bituminous base and cap sheet membrane flashing installed as per manufacturer's published application specifications.
+;(3) [[SBS Roof Systems Standard#PART_14|'''Pre-Curb (Start-Up Curb) Membrane Flashing''']]: Modified Bituminous base and cap sheet membrane flashing installed as per manufacturer's published application specifications.
-;(4) [[SBS Roof Systems Standard#SBSLIQUIDDETAILS|'''Proprietary Liquid Membrane Flashing''']]: RoofStar Guarantee Program accepted Liquid Membrane Flashing System(s) or hot melt SBS modified bitumen. (NOTE: Refer to [[Flexible Membrane Roofing Systems: Liquid Membrane Flashing Systems|'''Liquid Membrane Flashing Systems''']] in the Accepted Materials section of this Manual). Install as per Manufacturer's published instructions.
+;(4) [[SBS Roof Systems Standard#PART_10|'''Proprietary Liquid Membrane Flashing''']]: RoofStar Guarantee Program accepted Liquid Membrane Flashing System(s) or hot melt SBS modified bitumen. (NOTE: Refer to '''Liquid Membrane Flashing Systems''' in Division C of this Manual). Install as per Manufacturer's published instructions.
-;(5)  [[SBS Roof Systems Standard#SBS-STRIPPING|'''Inside Planter Wall Membrane Flashing''']]: Adhered according to manufacturer's specifications using cold adhesive, self-adhered or torch-applied membrane.  Torching directly to wood surfaces is not permitted. Carry membrane flashing plies to reglet termination near top of planter wall (stagger membrane seal minimum 300mm (6").
+;(5)  [[SBS Roof Systems Standard#PART_14|'''Inside Planter Wall Membrane Flashing''']]: Adhered according to manufacturer's specifications using cold adhesive, self-adhered or torch-applied membrane.  Torching directly to wood surfaces is not permitted. Carry membrane flashing plies to reglet termination near top of planter wall (stagger membrane seal minimum 300mm (6").
-;(6)  [[SBS Roof Systems Standard#METALCAP-SBS|'''Reglet - Metal Counter Flashing''']]: As required by the ''RoofStar Guarantee Standards''.  Note that a coping flashing may be paired with the reglet flashing, as illustrated.
+;(6)  [[SBS Roof Systems Standard#PART_13|'''Reglet - Metal Counter Flashing''']]: As required by the ''RoofStar Guarantee Standards''.  Note that a coping flashing may be paired with the reglet flashing, as illustrated.
 ;(7)  '''Plaza Deck / Planter Interior Assembly''': Extruded polystyrene insulation and filter mat over primary roof membranes. Concrete pavers placed above pre-curb membrane flashing height, on proprietary pedestals. Note: membrane flashing is not permitted above pre-curb membrane flashing on plaza deck side of planter walls.
@@ Line 36: / Line 36: @@
 === RELATED WORK BY OTHERS ===
-;(A) [[SBS Roof Systems Standard#SBSDECKS|'''Acceptable Supporting Deck Structure''']]: Concrete slab shown. Each planter area must have a drain through the roof deck.
+;(A) [[SBS Roof Systems Standard#PART_2|'''Acceptable Supporting Deck Structure''']]: Concrete slab shown. Each planter area must have a drain through the roof deck.
 ;(B) '''Pre-Curb''': Minimum of 100mm (4") in height above concrete deck, smooth dry and clean.
 ;(C) '''Cast over Concrete Planter Wall''': Form on top of membrane sealed Pre-curbs or Start-up curbs.
 ;(D) '''Re-Bar''': Placed at centre of Pre-curb.
-;(E) [[SBS Roof Systems Standard#METALCAP-SBS|'''Reglet''']]: Premanufactured purpose-made reglet cast in concrete wall or saw-cut.
+;(E) [[SBS Roof Systems Standard#PART_13|'''Reglet''']]: Premanufactured purpose-made reglet cast in concrete wall or saw-cut.
 ;(F) '''Alternate Termination''': Horizontal Reglet alternative to pre-manufactured purpose-made reglet, cast in concrete wall or saw-cut on vertical surface of inside planter walls.
 </div><!-- COL-6-MD -->

@@ Line 11: / Line 11: @@
 <div class="col-md-6">
 <div style="text-align:center; vertical-align:center">
-[[File:D1.7.6-5 (1).jpg|class=img-responsive]]
+[[File:D1.7.6-5 (1).jpg| link=http://rpm.rcabc.org/images/5/51/D1.7.6-5_%281%29.jpg | class=img-responsive]]
-[[File:D1.7.6-5 (2).jpg|class=img-responsive]]
+[[File:D1.7.6-5 (2).jpg| link=http://rpm.rcabc.org/images/c/ca/D1.7.6-5_%282%29.jpg | class=img-responsive]]
 </div>

@@ Line 50: / Line 50: @@
 <hr>
-[[SBS Roof System Details|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''SBS-modified Bitumen Membrane Roof System Details'']]
+[[SBS Roof System Details|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''"SBS" Roof System Details'']]
 [[Main Page | <i class="fa fa-home fa"></i> Home]]
 {{Tempate:RPM Page Footer with Copyright and Current Date}}