Template:Part 10 (Waterproofing Roofs - Single-ply) - Revision history

James Klassen: /* General */

2021-11-12T19:00:02Z

‎General

James Klassen at 14:07, 14 April 2021

2021-04-14T14:07:22Z

James Klassen at 21:34, 5 February 2021

2021-02-05T21:34:40Z

Show changes

James Klassen: /* {{hilite | Parapets|| 2021-October-30 }} */

2020-11-26T19:34:13Z

‎{{hilite | Parapets|| 2021-October-30 }}

James Klassen: /* {{hilite | Parapets|| 2021-October-30 }} */

2020-11-26T19:27:57Z

‎{{hilite | Parapets|| 2021-October-30 }}

James Klassen: /* {{hilite | Parapets|| 2021-October-30 }} */

2020-11-26T19:15:10Z

‎{{hilite | Parapets|| 2021-October-30 }}

James Klassen: /* All Projects */

2020-11-26T14:52:58Z

‎All Projects

James Klassen: /* All Projects */

2020-11-26T14:51:21Z

‎All Projects

James Klassen: /* All Projects */

2020-11-26T14:50:31Z

‎All Projects

James Klassen at 15:50, 2 November 2020

2020-11-02T15:50:35Z

Show changes

@@ Line 141: / Line 141: @@
 ====[NOT USED]====
 <div id="MEMB_PERIM_MATERIALS"></div>
 ==Materials==
 ===Membranes===

@@ Line 10: / Line 10: @@
 :;''Tall parapet'': means a parapet taller than 600 mm (24”).
 ;:
+<div id="MEMB_PERIM_DESIGN"></div>
 ===Design===
 ====RoofStar 15-Year Guarantee====
@@ Line 140: / Line 140: @@
 ====[NOT USED]====
+<div id="MEMB_PERIM_MATERIALS"></div>
 ==Materials==
 ===Membranes===
@@ Line 159: / Line 159: @@
 <li>{{hilite | ''Linear metal flashings'' incorporated into roof perimeters and ''walls'' must conform to the materials and fabrication standards found in '''13.2 Materials'''|| 2020-July-3 }}.
 </li></ol>
-<div id="FIELDAPPLICATION"></div>
+<div id="MEMB_PERIM_APPLICATION"></div>
 ==Application==
 ===General===
@@ Line 261: / Line 260: @@
 </div>
 </div>
+<div id="MEMB_PERIM_PARAPETS"></div>
 ===={{hilite | Parapets|| 2021-October-30 }}====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 289: / Line 288: @@
 </li></ol>
 </li></ol>
+<div id="MEMB_PERIM_LOW_EDGE"></div>
 ===={{hilite | Low Roof Edges|| 2021-October-30 }}====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 322: / Line 321: @@
 </li></ol>
 </li></ol>
+<div id="MEMB_PERIM_WALLS"></div>
 ===={{hilite | Walls|| 2021-October-30 }}====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 341: / Line 340: @@
 </li></ol>
 </li></ol>
+<div id="MEMB_PERIM_TRANSIT_WS"></div>
 ===={{hilite | Transitions with Water-Shedding Systems|| 2021-October-30 }}====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 364: / Line 363: @@
 </li></ol>
 </li></ol>
+<div id="MEMB_PERIM_EXPANSION"></div>
 ====Expansion and Control Joints====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 381: / Line 380: @@
 <li>Field splicing of proprietary elastomeric ''expansion joints'' is permitted only when made with a machine acceptable to the ''expansion joint'' manufacturer. All other field splices are not permitted.
 </li></ol>
+<div id="MEMB_PERIM_LOW_OPENING"></div>
 ===={{hilite | Low|| 2022-February-5 }} Door and Window Openings====
 {{hilite | In addition to the general requirements in Article 10.3.1.2, the following standards apply|| 2021-October-30 }}:
@@ Line 432: / Line 431: @@
 <li><span class="recommended">{{hilite | Overhangs above the door are recommended wherever practical, to minimize water intrusion that occurs from wind-driven rain or from snow accumulation|| 2022-February-5}}</span>.
 </li></ol>
+<div id="MEMB_PERIM_MEMBRANES"></div>
 ===Membranes===
 ====[NOT USED]====

@@ Line 59: / Line 59: @@
 {{hilite | In addition to the general requirements in Article 10.1.2.2, the following standards apply|| 2021-October-30 }}:
 <ol>
-<li>{{hilite | '''Conventionally Insulated Roofs''': ''Parapets'' are not required for ''Conventionally Insulated Roofs'', but when they are specified the ''parapet'' must be no less than 125 mm (5") in height, measured from the top of the ''Finished Waterproofing System'' to the inside top edge of the ''parapet'' (to facilitate proper metal cap flashing securement).  See also '''13.3.4 Cap, Counter and Base Flashings'''|| 2021-October-30 }}.
+<li>{{hilite | '''Conventionally Insulated Roofs''': ''Parapets'' are not required for ''Conventionally Insulated'' roofs, but when they are specified the ''parapet'' must be no less than 125 mm (5") in height, measured from the top of the ''Finished Waterproofing System'' to the inside top edge of the ''parapet'' (to facilitate proper metal cap flashing securement).  See also '''13.3.4 Cap, Counter and Base Flashings'''|| 2021-October-30 }}.
 <li>{{hilite | '''Roofs with Overburden or Ballast''': ''Parapets'' (or a retention system for ''Overburden'' or ballast that is acceptable to the ''Guarantor'') are required for <u>any roof</u> that supports ''Overburden'' or ballast, and the parapet or retention system must be at least 200 mm (8”) in height when measured from the ''Finished Waterproofing System'', in order to retain the ''Overburden'' or ballast against wind scouring.  This minimum height requirement may be reduced for ''Vegetated Roof Systems'' if the reduced height is supported by an independently conducted wind test and published report (See also '''Part 3 SECURING the ROOF ASSEMBLY'''.  See also Sub-article 14.1.2.2.3, Vegetated Roof Systems, for additional securement standards)|| 2021-October-30 }}.
 <li>{{hilite | All membranes installed on ''parapets'' must be fully adhered to the ''parapet'' substrate|| 2021-October-30 }}.

@@ Line 61: / Line 61: @@
 <li>{{hilite | '''Conventionally Insulated Roofs''': ''Parapets'' are not required for ''Conventionally Insulated Roofs'', but when they are specified the ''parapet'' must be no less than 125 mm (5") in height, measured from the top of the ''Finished Waterproofing System'' to the inside top edge of the ''parapet'' (to facilitate proper metal cap flashing securement).  See also '''13.3.4 Cap, Counter and Base Flashings'''|| 2021-October-30 }}.
 <li>{{hilite | '''Roofs with Overburden or Ballast''': ''Parapets'' (or a retention system for ''Overburden'' or ballast that is acceptable to the ''Guarantor'') are required for <u>any roof</u> that supports ''Overburden'' or ballast, and the parapet or retention system must be at least 200 mm (8”) in height when measured from the ''Finished Waterproofing System'', in order to retain the ''Overburden'' or ballast against wind scouring.  This minimum height requirement may be reduced for ''Vegetated Roof Systems'' if the reduced height is supported by an independently conducted wind test and published report (See also '''Part 3 SECURING the ROOF ASSEMBLY'''.  See also Sub-article 14.1.2.2.3, Vegetated Roof Systems, for additional securement standards)|| 2021-October-30 }}.
-<li>{{hilite | All membranes installed on ''parapets'' must be fully adhered to the parapet substrate|| 2021-October-30 }}.
+<li>{{hilite | All membranes installed on ''parapets'' must be fully adhered to the ''parapet'' substrate|| 2021-October-30 }}.
 </li></ol>

@@ Line 60: / Line 60: @@
 <ol>
 <li>{{hilite | '''Conventionally Insulated Roofs''': ''Parapets'' are not required for ''Conventionally Insulated Roofs'', but when they are specified the ''parapet'' must be no less than 125 mm (5") in height, measured from the top of the ''Finished Waterproofing System'' to the inside top edge of the ''parapet'' (to facilitate proper metal cap flashing securement).  See also '''13.3.4 Cap, Counter and Base Flashings'''|| 2021-October-30 }}.
-<li>{{hilite | '''Roofs with Overburden or Ballast''': ''Parapets'' (or a retention system for ''Overburden'' or ballast that is acceptable to the Guarantor) are required for <u>any roof</u> that supports ''Overburden'' or ballast, and the parapet or retention system must be at least 200 mm (8”) in height when measured from the ''Finished Waterproofing System'', in order to retain the ''Overburden'' or ballast against wind scouring.  This minimum height requirement may be reduced for ''Vegetated Roof Systems'' if the reduced height is supported by an independently conducted wind test and published report (See also '''Part 3 SECURING the ROOF ASSEMBLY'''.  See also Sub-article 14.1.2.2.3, Vegetated Roof Systems, for additional securement standards)|| 2021-October-30 }}.
+<li>{{hilite | '''Roofs with Overburden or Ballast''': ''Parapets'' (or a retention system for ''Overburden'' or ballast that is acceptable to the ''Guarantor'') are required for <u>any roof</u> that supports ''Overburden'' or ballast, and the parapet or retention system must be at least 200 mm (8”) in height when measured from the ''Finished Waterproofing System'', in order to retain the ''Overburden'' or ballast against wind scouring.  This minimum height requirement may be reduced for ''Vegetated Roof Systems'' if the reduced height is supported by an independently conducted wind test and published report (See also '''Part 3 SECURING the ROOF ASSEMBLY'''.  See also Sub-article 14.1.2.2.3, Vegetated Roof Systems, for additional securement standards)|| 2021-October-30 }}.
 <li>{{hilite | All membranes installed on ''parapets'' must be fully adhered to the parapet substrate|| 2021-October-30 }}.
 </li></ol>

@@ Line 25: / Line 25: @@
 <ol>
 <li>{{hilite | Turning the field membrane up the vertical surface|| 2021-October-30 }}.
-<li>{{hilite | Flashing the vertical surface with membrane flashing (see '''10.3.2 Membranes'''). All membrane flashing must extend at least 200 mm (8”) above the ''Finished Waterproofing System''.  Parapets less than 200 mm (8") in height, ''Low Door'' or ''Low Window'' applications (see Article 10.3.1.8) are exempt from this standard|| 2021-October-30 }}.
+<li>{{hilite | Flashing the vertical surface with membrane flashing (see '''10.3.2 Membranes'''). All membrane flashing must extend at least 200 mm (8”) above the ''Finished Waterproofing System''.  Low parapets, ''Low Door'' or ''Low Window'' applications (see Article 10.3.1.8) are exempt from this standard|| 2021-October-30 }}.
 </li></ol>
 <li>{{hilite | All membranes installed on ''parapets'', over a low roof edge or on ''walls'' must|| 2021-October-30 }}