Search results

Create the page "Insulation" on this wiki! See also the search results found.

Template:Part 14 - TPO
...signed as a ''Protected Membrane Roof System''. See also '''8.1.1 Design (Insulation Overlays)'''. ..."fines" from settling at the membrane level and filling the voids between insulation board joints.

32 KB (4,724 words) - 17:43, 16 November 2021
Template:Part 1 - PVC
<li>{{hilite | An insulation overlay is required on all ''Conventionally Insulated Roof Systems'' || 202 <li>''Uninsulated Systems''(insulation may be installed beneath the deck).

35 KB (4,973 words) - 17:31, 22 November 2021
Template:Part 2 - PVC
...tructure with sloped ''decks'', or by introducing slope with tapered board insulation. :See also '''Part 7 INSULATION'''.

25 KB (3,582 words) - 14:50, 23 December 2021
Template:Part 3 - PVC
| Insulation || #12 || 73 mm (2-7/8”) Hexagonal, 76 mm (3”) Round or Square | Insulation Overlays || #12 || 73 mm (2-7/8”) Hexagonal, 76 mm (3”) Round or Squar

55 KB (7,513 words) - 20:12, 22 April 2022
Template:Part 5 - PVC
...rs, or to serve as a thermal barrier between the roof deck and combustible insulation. Roof ''deck'' overlay materials may also be applied to other types of sup

6 KB (959 words) - 18:34, 15 November 2021
Template:Part 7 - PVC
...tion materials will resist burning for a period of time, only mineral wool insulation will not burn. ...for example, heat from a torch or from liquefied bitumen. Heat-sensitive insulation includes EPS, XPS and polyurethane.

18 KB (2,507 words) - 19:23, 16 November 2021
Template:Part 8 - PVC
...ation overlay is required for all insulated ''systems'', regardless of the insulation type, and overlays must ...flat and sloped ||2021-June-30 }} board-type insulation, {{hilite | and on insulation installed on vertical surfaces|| 2021-June-30 }},

10 KB (1,372 words) - 15:36, 16 November 2021
Template:Part 9 - PVC
<li>accepted concrete-topped XPS insulation panels. <li>XPS insulation panels with drainage grooves or channels.

29 KB (2,996 words) - 17:31, 15 June 2022
Template:Part 10 - PVC
<li>{{hilite | When EIFS cladding is cut to permit roofing work, the exposed insulation must be restored with back-wrapped mesh, a base coat and finish coat, or wi

36 KB (5,070 words) - 14:53, 17 November 2021
Template:Part 11 - PVC
...(see '''7.1.3.5'''). Sumps designed with sloped insulation are strongly recommended. ...standards for sleepers or equipment pads. A separation layer between XPS insulation and PVC membranes is required, to prevent leaching of plasticizers from the

45 KB (6,830 words) - 19:37, 11 March 2022
Template:Part 12 - PVC
<li>a drainage layer beneath XPS insulation. <li>filter fabric installed over XPS insulation, in order to

14 KB (2,184 words) - 18:37, 15 November 2021
Template:Part 13 - PVC
...stalled. Metal base flashings must “kick out” minimum 50 mm (2") over insulation and filter fabric. Filter fabric must be tucked up behind the base flashin

28 KB (4,147 words) - 21:43, 27 April 2022
Template:Part 14 - PVC
...signed as a ''Protected Membrane Roof System''. See also '''8.1.1 Design (Insulation Overlays)'''. ..."fines" from settling at the membrane level and filling the voids between insulation board joints.

32 KB (4,724 words) - 17:43, 16 November 2021
Template:Header - SBS
| [[#PART_7 | PART 7 - Insulation]] | [[#PART_8 | PART 8 - Insulation Overlays]]

3 KB (419 words) - 21:58, 15 November 2021
Template:Header - EPDM
| [[#PART_7 | PART 7 - Insulation]] | [[#PART_8 | PART 8 - Insulation Overlays]]

3 KB (415 words) - 21:58, 15 November 2021
Template:Header - TPO
| [[#PART_7 | PART 7 - Insulation]] | [[#PART_8 | PART 8 - Insulation Overlays]]

3 KB (412 words) - 21:58, 15 November 2021
Template:Header - PVC
| [[#PART_7 | PART 7 - Insulation]] | [[#PART_8 | PART 8 - Insulation Overlays]]

3 KB (412 words) - 21:59, 15 November 2021
(Draft) Notes to Hot Rubber Standard
...ng system'' is defined by whatever is placed on the membrane, which may be insulation, ballast, pavers or overburden. These materials will displace water and th ...roof membrane, while retaining existing ''roof system'' components (i.e., insulation, ballast).

41 KB (6,077 words) - 18:11, 2 April 2024
Notes to Hot Rubber Standard
...ng system'' is defined by whatever is placed on the membrane, which may be insulation, ballast, pavers or overburden. These materials will displace water and th ...roof membrane, while retaining existing ''roof system'' components (i.e., insulation, ballast).

41 KB (6,080 words) - 18:16, 2 April 2024
TPO Metal Edge Termination
...d). Installed according to ''RoofStar Guarantee Standards''. See available insulation products in the [[Division C|'''Accepted Materials''']] Division of this Ma ...yed (3A: 2- part low rising insulation adhesive, specifically used to bond insulation and cover boards)

4 KB (592 words) - 18:24, 21 September 2022