View source for ASM Eave and Rake Edges (Copper)

{{Template:RPM Info}}

{{DISPLAYTITLE:<span style="position: absolute; clip: rect(1px 1px 1px 1px); clip: rect(1px, 1px, 1px, 1px);">{{FULLPAGENAME}}</span>}}
__NOTOC__

<big><big>Division D - Construction Details</big></big>
<hr>
<big><big><big><big><big>ASM | Eave and Rake Edges (Copper) ([[ASM_Roof_Systems_Standard#10.3.2.3. General Application Requirements for Perimeters and Walls | Article 10.3.2.3.]] and [[ASM_Roof_Systems_Standard#10.3.4.2. Eaves and Rake Edges | Article 10.3.4.2.]])</big></big></big></big></big>
{{Template:Construction Details Header}}
<div class="panel panel-success">
<div class="panel-heading"><big>'''SBS Details'''</big></div>
<div class="panel-body">
<div class="col-md-6">
<div style="text-align:center; vertical-align:center">
[[File:ASM 10.1.3 Eave and Rake Flashing (Copper).jpg|class=img-responsive | link=http://rpm.rcabc.org/images/4/4a/ASM_10.1.3_Eave_and_Rake_Flashing_%28Copper%29.jpg]]
</div>


::Click below for a printable version of this page (N/A)

<div style="width:150px; text-align: left;">
:[[File:Pdf.png|100 px|link=|'''Print Sheet''']]
</div>

</div><!-- COL-MD-6 -->
<div class="col-md-6">
=== WORK INCLUDED ===
;(1) [[ASM Roof Systems Standard#8.1.3.4. Separation Between Materials  | '''Separation membrane''']]: Separates the deck and the metal edge flashing.
;(2) [[ASM Roof Systems Standard#10.3.4.2. Eaves and Rake Edges | '''Hook securement strip''']]: In this particular rake edge configuration, a similar strip is installed along the rake to secure the flush rake-edge flashing.
;(3) [[ASM Roof Systems Standard#10.3.4.2. Eaves and Rake Edges | '''Continuous eave metal flashing''']]:
;(4) [[ASM Roof Systems Standard#8.1.3.1. Eave Protection|'''Eave protection''']]: One ply of self-adhered modified bituminous underlayment material. Lap 50 mm (2") minimum on sides and 100 mm (4") minimum on ends.
;(5) [[ASM Roof Systems Standard#8.1.3.3. Field Underlayment|'''Underlayment''']]: Applicable for all Architectural Sheet Metal systems.  For slopes less than 1:3, the entire roof slope must be covered with a <u>self-adhered</u> underlayment.
;(6) [[ASM Roof Systems Standard#8.1.3.5. Ventilation Beneath Panels|'''Ventilation beneath panels''']]: A ventilation space is required on slopes less than 1:3; entangled mesh (shown) may be used as void fill.  The ventilation space facilitates drying as condensation forms on the underside of the metal panels.
;(7) [[ASM Roof Systems Standard#9.2.1.5.Clips|'''Metal panel clip''']]: Installed in keeping with the metal roof panel manufacturer's printed instructions. Install on EPDM pad (not shown) or use a tall clip sized to support the panel on top of the ventilation layer.
;(8) [[ASM Roof Systems Standard#10.3.4.2. Eaves and Rake Edges | '''Flush rake-edge flashing''']]: Note that panel hooks onto outside edge of flashing, which is mechanically secured to the roof deck.
;(9) [[ASM Roof Systems Standard#PART_9|'''Architectural metal roof panel''']]

<hr>

=== RELATED WORK BY OTHERS ===
;(A) [[ASM Roof Systems Standard#PART_2|'''Acceptable deck''']]
;(B) '''Fascia Board''' 
</div><!-- COL-6-MD -->
</div><!-- PANEL BODY -->
</div><!-- PANEL -->

'''NOTE''': See the [[ASM Roof Systems Standard | '''Standard''']] for additional requirements.

<hr>

[[ASM Roof System Details|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''ASM Roof System Details'']]

[[Main Page | <i class="fa fa-home fa"></i> Home]]

{{Tempate:RPM Page Footer with Copyright and Current Date}}