View source for ASM Membrane Gutter (Insulated Assembly)

{{Template:RPM Info}}

{{DISPLAYTITLE:<span style="position: absolute; clip: rect(1px 1px 1px 1px); clip: rect(1px, 1px, 1px, 1px);">{{FULLPAGENAME}}</span>}}
__NOTOC__

<big><big>Division D - Construction Details</big></big>
<hr>
<big><big><big><big><big>ASM | Membrane Gutter (Insulated Assembly) ([[ASM_Roof_Systems_Standard#11.1.4.3.._Membrane_Gutters | Article 11.1.4.3.]] and [[ASM_Roof_Systems_Standard#11.3.3.8._Membrane_Gutters | Article 11.3.3.8.]])</big></big></big></big></big>
{{Template:Construction Details Header}}
<div class="panel panel-success">
<div class="panel-heading"><big>'''ASM Details'''</big></div>
<div class="panel-body">
<div class="col-md-6">
<div style="text-align:center; vertical-align:center">
[[File:ASM 12.1.2 Built-in Gutter Assembly UPLOADED.jpg|class=img-responsive | link=http://rpm.rcabc.org/images/5/5f/ASM_12.1.2_Built-in_Gutter_Assembly_UPLOADED.jpg]]
</div>

::Click below for a printable version of this page (N/A)

<div style="width:150px; text-align: left;">
:[[File:Pdf.png|100 px|link=http://rpm.rcabc.org/images/5/52/D1.7.6-3_Print_Sheet.pdf|'''Print Sheet''']]
</div>


</div><!-- COL-MD-6 -->

<div class="col-md-6">
=== WORK INCLUDED ===
;(1) [[ASM Roof Systems Standard#PART_5|'''Deck overlay''']]: Required for continuous support of the underlayment when the deck is not suitable.
;(2) [[ASM Roof Systems Standard#8.1.3.3. Field Underlayment|'''Underlayment (lower)''']]: The type of underlay required is determined by roof slope. 
;(3) Wood blocking
;(4) [[ASM Roof Systems Standard#PART_7|'''Insulation''']]: Tapered to support gutter membrane, which is tied into underlayment, to ensure any water intrusion into roof system drains into gutter.
;(5) [[ASM Roof Systems Standard#11.1.4.3.. Membrane Gutters |'''Gutter Membrane''']]
;(6) [[ASM Roof Systems Standard#8.1.3.3. Field Underlayment|'''Underlayment (upper)''']]
;(7) [[ASM Roof Systems Standard#PART_7| '''Upper insulation''']]: Tapered at lower edge to conform to lower insulation slope.  All flat panels must be offset and stagger layers 300 mm (12").
;(8) [[ASM Roof Systems Standard#8.1.3.4. Separation Between Materials|'''Vapour-permeable separation membrane''']]: Installed over insulation and required on all insulated Architectural Sheet Metal Roof Systems.  The material must be located between the insulation and metal panels/ventilation material (see [http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_Architectural_Sheet_Metal_(ASM)_Systems#Design_5 '''8.1.2 Design'''])).
;(9) [[ASM Roof Systems Standard#8.1.3.5. Ventilation Beneath Panels|'''Ventilation beneath panels''']]: Recommended over asphaltic underlays and / or as required in this Standard (see [http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_Architectural_Sheet_Metal_(ASM)_Systems#Design_5 '''8.1.2 Design''']).
;(10) [[ASM Roof Systems Standard#9.2.1.6. Bearing Plates and EPDM Pads|'''Bearing plate''']]: Only thermally non-conductive clips or bars passing through the insulation assembly, or mechanically fastened bearing plates, may be used to secure and support insulation panels, or provide support for panel clips.
;(11) [[ASM Roof Systems Standard#9.2.1.5.Clips |'''Architectural metal panel clip''']]
;(12) [[ASM Roof Systems Standard#PART_9 |'''Architectural metal roof panel''']]: Lower, installed prior to the pipe flashing, cut hole large enough to allow for movement. Extend 400 mm (16") upslope beyond the pipe.
;(13) Mastic (2-ply SBS) or Sealant (Single plies): Drain flange must be embedded in a membrane-compatible mastic and secured to the gutter structure.
;(14) [[ASM Roof Systems Standard#PART_11 |'''Drain Body''']]: Mechanically secured through flange (for all drain types, see '''Part 11 DRAINS and PENETRATIONS''' in the relevant membrane standard in this ''Manual'').
;(15) Strainer
;(16) [[ASM Roof Systems Standard#11.1.4.3.. Membrane Gutters |'''Gutter Membrane''']]: Refer to the relevant membrane standard for application requirements (SBS, EPDM, TPO or PVC).
;(17) [[ASM Roof Systems Standard#PART_13 |'''Parapet cap flashing''']]

<hr>

=== RELATED WORK BY OTHERS ===
;(A) [[ASM Roof Systems Standard#PART_2|'''Acceptable Deck''']]
;(B) '''Built-in Gutter structure'''.  Sloped to drain.
;(C) '''Parapet'''
</div><!-- COL-6-MD -->
</div><!-- PANEL BODY -->
</div><!-- PANEL -->

'''NOTE''': See the [[ASM Roof Systems Standard | '''Standard''']] for additional requirements.

<hr>

[[ASM Roof System Details|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''ASM Roof System Details'']]

[[Main Page | <i class="fa fa-home fa"></i> Home]]

{{Tempate:RPM Page Footer with Copyright and Current Date}}