Difference between revisions of "SBS Parapet (Typical)"

Revision as of 22:07, 18 July 2016

1 WORK INCLUDED

1. Gypsum Board: If required by design authority.
2. Vapour Retarder: If required by design authority.
3. Insulation: See list of Accepted Materials.
4. Insulation Overlay Board: As required.
5. Primary Membrane and Membrane Protection
6. Membrane Flashing: Mechanically fasten to outside face of parapet blocking (D). At least one ply must extend over outside edge. See Perimeter Flashings: Membrane for RoofStar Guarantee Standards.
7. Metal Base Flashing: Optional on flexible membrane systems. Required on assemblies using gravel ballast filter mats.
8. Metal Cap Flashing: Flashings 1 and 2 may be one piece. Fasten with continuous concealed clip-type fasteners or cladding screws evenly spaced between seams. See Perimeter Metal Flashings for requirements.

2 RELATED WORK BY OTHERS

(A) Acceptable Deck

(B) Air / Vapour Seal

(C) Acceptable Wall Surface

(D) Wood Blocking

(E) Sloped Wood Blocking: Required over 100 mm (4") parapet width. See RGC Guarantee Standard A6.9

NOTE: Refer to RGC Guarantee Standards for additional requirements.]

Back to SBS Application

Back to SBS Construction Details

Back to Construction Details

@@ Line 3: / Line 3: @@
 === WORK INCLUDED ===
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSSUBSTRATES|'''Gypsum Board''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSSUBSTRATES|'''1. Gypsum Board''']]:
 :If required by design authority.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSVAPOUR|'''Vapour Retarder''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSVAPOUR|'''2. Vapour Retarder''']]:
 :If required by design authority.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSINSULATION|'''Insulation''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSINSULATION|'''3. Insulation''']]:
 :See list of '''[[Section:C. Accepted Materials|Accepted Materials]]'''.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSINSULATIONOVERLAY|'''Insulation Overlay Board''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSINSULATIONOVERLAY|'''4. Insulation Overlay Board''']]:
 :As required.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSBASE|'''Primary Membrane and Membrane Protection''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBSBASE|'''5. Primary Membrane and Membrane Protection''']]:
-;[[RoofStar Guarantee Standards for SBS Roof Systems#SBS-STRIPPING|'''Membrane Flashing''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#SBS-STRIPPING|'''6. Membrane Flashing''']]:
 :Mechanically fasten to outside face of parapet blocking (D). At least one ply must extend over outside edge. See '''Perimeter Flashings: Membrane''' for RoofStar Guarantee Standards.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#METALBASE-SBS|'''Metal Base Flashing''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#METALBASE-SBS|'''7. Metal Base Flashing''']]:
 :Optional on flexible membrane systems. Required on assemblies using gravel ballast filter mats.
-;[[RoofStar Guarantee Standards for SBS Roof Systems#METALCAP-SBS|'''Metal Cap Flashing''']]:
+;[[RoofStar Guarantee Standards for SBS Roof Systems#METALCAP-SBS|'''8. Metal Cap Flashing''']]:
 :Flashings 1 and 2 may be one piece.  Fasten with continuous concealed clip-type fasteners <b>or</b> cladding screws evenly spaced between seams. See '''Perimeter Metal Flashings''' for requirements.