Difference between revisions of "ASM Cylindrical Penetration (Split Panel Flashing)"

Revision as of 22:08, 24 April 2019

RoofStar Guarantee Standards are blue-linked

ASM Details

Click below for a printable version of this page.

1 WORK INCLUDED

(1) Architectural Metal Roof Panel: Lower, installed prior to the pipe flashing, cut hole large enough to allow for movement. Extend 400 mm (16") upslope beyond the pipe.
(2) Settlement Cap: Material must match flashing material.
(3) Drag-load Fasteners: Compatible non-corrosive fasteners.
(4) Sealant Tape: Two rows of sealant tape or acceptable caulking.
(5) Caulking: Bead of caulking tooled into transition between metal roof panel and flashing.
(6) Protrusion Flashing: Flange set in two continuous beads of accepted caulking.
(7) Metal Clip on Bearing Plate.
(8) Separation Layer (Drainage Mat): Required for slopes less than 1:3; recommended over asphaltic underlays and / or as required by metal roof panel manufacturer.
(9) Underlayment: The type of underlay required is determined by roof slope.
(10) Spaced Cleat: Cleats, set in accepted caulking, spaced 50 mm (2") and fastened with compatible non-corrosive flat head screws.
(11) Architectural Metal Roof Panel: Upper, installed after installation of pipe flashing. Cut hole for pipe penetration and turn panel end under to accommodate cleats.

2 RELATED WORK BY OTHERS

(A) Acceptable Deck

NOTE: Refer to RoofStar Guarantee Standards for additional requirements.

RoofStar Guarantee Standards for ASM Roof Assemblies

Back to ASM Construction Details

Back to Construction Details

@@ Line 9: / Line 9: @@
 [[File:8.1.4.9.1.jpg|class=img-responsive]]
 </div>
 ::Click below for a printable version of this page.
 <div style="width:150px; text-align: left;">
-:[[File:Pdf.png|100 px|link=http://rpm.rcabc.org/images/6/6b/ASM_E1.7.9_%28Equipment_Support_Stand_-_Pipe_Flashing_Split_Panel_Detail%29.pdf]]
+:[[File:ASM 11.1 Thumb for PDF.jpg|100 px|link=http://rpm.rcabc.org/images/8/8d/ASM_11.2_Pipe_Flashing%2C_Split_Panel.pdf|'''Print Sheet''']]
 </div>
 </div><!-- COL-MD-6 -->
@@ Line 21: / Line 19: @@
 <div class="col-md-6">
 === WORK INCLUDED ===
-;(1) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMUNDERLAYMENT|'''Underlayment''']]: The type of underlay required is determined by roof slope.
+;(1) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMPANEL |'''Architectural Metal Roof Panel''']]: Lower, installed prior to the pipe flashing, cut hole large enough to allow for movement. Extend 400 mm (16") upslope beyond the pipe.
-;(2) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMSLIP|'''Slip Sheet''']]: Recommended over asphaltic underlays and / or as required by metal roof panel manufacturer.
+;(2) '''Settlement Cap''': Material must match flashing material.
-;(3) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMPANEL |'''Architectural Metal Roof Panel''']]: Lower, installed prior to the pipe flashing, cut hole large enough to allow for movement. Extend 400 mm (16") upslope beyond the pipe.
+;(3) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMDRAG |'''Drag-load Fasteners''']]: Compatible non-corrosive fasteners.
-;(4) '''Flashing''':  Flange set in two continuous beads of accepted caulking.
+;(4) '''Sealant Tape''': Two rows of sealant tape or acceptable caulking.
-;(5) '''Spaced Cleat''': Cleats, set in accepted caulking, spaced 50 mm (2") and fastened with compatible non-corrosive flat head screws.
+;(5) '''Caulking''': Bead of caulking tooled into transition between metal roof panel and flashing.
-;(6) '''Architectural Metal Roof Panel''': Upper, installed after installation of pipe flashing.  Cut hole for pipe penetration and turn panel end under to accommodate cleats.
+;(6) '''Protrusion Flashing''':  Flange set in two continuous beads of accepted caulking.
-;(7) '''Settlement Cap''': Material must match flashing material.
+;(7) '''Metal Clip on Bearing Plate'''.
-;(8) '''Caulking''': Bead of caulking tooled into transition between metal roof panel and flashing.
+;(8) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMSLIP|'''Separation Layer (Drainage Mat)''']]: Required for slopes less than 1:3; recommended over asphaltic underlays and / or as required by metal roof panel manufacturer.
-;(9) '''Sealant Tape''': Two rows of sealant tape or acceptable caulking.
+;(9) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMUNDERLAYMENT|'''Underlayment''']]: The type of underlay required is determined by roof slope.
-;(10) [[RoofStar Guarantee Standards for ASM Roof Assemblies#ASMDRAG |'''Drag-load Fasteners''']]: Compatible non-corrosive fasteners.
+;(10) '''Spaced Cleat''': Cleats, set in accepted caulking, spaced 50 mm (2") and fastened with compatible non-corrosive flat head screws.
+;(11) '''Architectural Metal Roof Panel''': Upper, installed after installation of pipe flashing.  Cut hole for pipe penetration and turn panel end under to accommodate cleats.
 <hr>