Difference between revisions of "Miscellaneous wordings 1"

Jump to: navigation, search

Difference between revisions of "Miscellaneous wordings 1"

(→‎2-ply Model (FINAL))
(→‎RoofStar 15-Year Guarantee)
Line 686: Line 686:
 
===RoofStar 15-Year Guarantee===
 
===RoofStar 15-Year Guarantee===
 
<ol>
 
<ol>
−
<li>To qualify for a '''''RoofStar 15-year (Waterproofing Roofs) Guarantee''''', each ''Project'' must be designed and constructed {{hilite | in compliance with both || 2021-February-7 }} the '''''RoofStar Guarantee Standards''''' and the membrane manufacturer’s 20-year {{hilite | System || 2021-February-7 }} Warranty standards.
+
<li>To qualify for a '''''RoofStar 15-year (Waterproofing Roofs) Guarantee''''', the following standards apply:
 +
<ol>
 +
<li>Each ''Project'' must be designed and constructed {{hilite | in compliance with both || 2021-February-7 }} the '''''RoofStar Guarantee Standards''''' and the membrane manufacturer’s 20-year {{hilite | System || 2021-February-7 }} Warranty standards.
 
<li>The ''Contractor'' must apply to the membrane manufacturer for their 20-year System Warranty standards.
 
<li>The ''Contractor'' must apply to the membrane manufacturer for their 20-year System Warranty standards.
−
<li>Where enhanced roof system securement is required by the manufacturer, which may exceed the securement required in a ''Tested Assembly'', an ''Assembly with Proven Past Performance'' or a custom-engineered securement, the higher securement requirements must be complied with.
+
<li>Where enhanced roof system securement is required by the manufacturer, which may exceed the securement required in a ''Tested Assembly'', an ''Assembly with Proven Past Performance'' or a custom-engineered securement, the ''Project'' must comply with the higher securement requirements.
 +
<li>In addition to the above, other requirements in this Standard apply, which can be summarized (without limitation) as follows:
 +
<ol>
 +
<li>Roofs must be designed for adequate access to facilitate maintenance ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Accessibility_for_Maintenance 1.3.3]).
 +
<li>Materials left in place for partial roof system replacement must be scanned for moisture ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Membrane_Replacement 1.4.2.2]).
 +
<li>All roofs (new construction and replacement roofing) must be built with a minimum slope of 2% (1:50) ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#New_Construction_2 2.2.2] and [http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Replacement_Roofing 2.2.3]).
 +
<li>All replacement roofing must utilize crickets to enhance drainage around curbs and sleepers ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Replacement_Roofing 2.2.3]).
 +
<li>Curbs and sleepers wider/longer than 1200 mm (48") must incorporate crickets to improve drainage ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#RoofStar_15-Year_Guarantee_4 7.1.2.1]).
 +
<li>An insulation overlay is required on all Conventionally Insulated Roof Systems ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#RoofStar_15-Year_Guarantee_6 8.1.1.1]).
 +
<li>Only certain membranes will qualify for a RoofStar 15-year Guarantee ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Materials_9 9.2]).
 +
<li>All drains and overflows require clamping rings, and overflows are required for each roof area ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#RoofStar_15-Year_Guarantee_12 11.1.2.1]).
 +
<li>Enhanced penetration flashing requirements ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#RoofStar_15-Year_Guarantee_13 11.1.3.1]).
 +
<li>Linear metal flashings must be fabricated from 24-gauge material ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#RoofStar_15-Year_Guarantee_15 13.1.2.1]).
 
</li></ol>
 
</li></ol>
−
<br>
 
−
In addition to the above, the following summary of RoofStar Guarantee Standards applies to all projects qualifying for a RoofStar 15-year Guarantee:
 
−
<ol>
 
−
<li>Roofs must be designed for adequate access to facilitate maintenance ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Accessibility_for_Maintenance '''1.3.3 Roof Access''']).
 
−
<li>Materials left in place for partial roof system replacement must be scanned for moisture ([http://rpm.rcabc.org/index.php?title=RoofStar_Guarantee_Standards_for_SBS_Modified_Bitumen_Membrane_Systems#Membrane_Replacement '''1.4.2.2 Membrane Replacement'''])
 
 
</li></ol>
 
</li></ol>
  
 
</div><!-- mainBodyDiv -->
 
</div><!-- mainBodyDiv -->
 
</div><!-- row -->
 
</div><!-- row -->

Revision as of 19:34, 23 November 2020

1 Single-ply 5/10-year

Table 9.1 Single-ply Membranes: RoofStar 5 and 10-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Conventionally Insulated / Uninsulated
Single-Ply Systems		 Ballasted
(Insulated /
Uninsulated)		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Loose-laid Adhered
or
Hot-mopped
(Smooth) 		Adhered Self-adhered,
Adhered
or
Hot-mopped 		Adhered
or
Hot-mopped
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.143 (45) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
EPDM (unreinforced) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
TPO 1.143 (45) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
PVC 1.270 (50) 1.270 (50) 2.667 (105) 1.270 (50) 1.270 (50) 1.524 (60) 1.524 (60) 1.524 (60)

2 Single-ply 15-year

Table 9.2 Single-ply Membranes: RoofStar 15-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Conventionally Insulated / Uninsulated
Single-Ply Systems		 Ballasted
(Insulated /
Uninsulated)		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Loose-laid Adhered
or
Hot-mopped
(Smooth) 		Adhered Self-adhered,
Adhered
or
Hot-mopped 		Adhered
or
Hot-mopped
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.524 (60) 1.524 (60) 2.032 (80) 2.032 (80)
EPDM (unreinforced) 1.524 (60) 1.524 (60) 2.790 (110) 1.524 (60) 2.032 (80) 2.032 (80)
TPO 1.524 (60) 1.524 (60) 1.524 (60) 2.790 (110) 1.524 (60) 2.286 (90) 2.286 (90)
PVC 1.524 (60) 1.524 (60) 2.667 (105) 1.524 (60) 2.286 (90) 2.286 (90)

3 SBS 5/10-year

Table 9.1 SBS-modified Bituminous Membranes: RoofStar 5 and 10-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Conventionally Insulated / Uninsulated
2-Ply Systems		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing		 Single-ply
Cap
Mech.
fastened 		Heat-
welded 		Self-
adhered 		Hot-
mopped 		Cold-
adhered 		Puncture
Resist.
Heat-welded / Adhered
Puncture Resistance
Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
As specified
Puncture Resistance
Type, Reinforcement, Grade mm mm mm mm mm (N) mm (N) mm (N) mm (N) mm (N) mm (N)
Base (fibreglass) - Grade 3 2.30 2.30 2.30 2.20 2.20 3.00 3.00 3.00
Base (polyester) - Grade 3 2.50 2.50 2.50 2.20 2.20 400 3.00 3.00 3.50 400 3.00
Base (composite) - Grade 3 2.30 2.30 2.30 2.20 2.20 400 3.00 3.00 3.50 3.00
Film Cap (fibreglass) - Grade 2 4.00 3.30 3.30 3.30 3.30
Film Cap (polyester) - Grade 2 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Film Cap (composite) - Grade 2 4.00 3.30 3.30 3.30 400 3.00 400 3.30 400 4.00 400 3.00 400 4.00 400
Granular Cap (fibreglass) - Grade 1 4.00 3.30 3.30 3.30 400 3.30
Granular Cap (polyester) - Grade 1 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Granular Cap (composite) - Grade 1 4.00 4.00 3.30 3.30 400 3.00 400 3.00 400 4.00 400 3.00 400 4.00 400


Table 9.1 SBS-modified Bituminous Membranes: RoofStar 5 and 10-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Conventionally Insulated / Uninsulated
2-Ply Systems		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing		 Single-ply
Cap
Mech.
fastened 		Heat-
welded 		Self-
adhered 		Hot-
mopped 		Cold-
adhered 		Puncture
Resist.
Heat-welded / Adhered
Puncture Resistance
Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
As specified
Puncture Resistance
Type, Reinforcement, Grade mm mm mm mm mm (N) mm (N) mm (N) mm (N) mm (N) mm (N)
Base (fibreglass) - Grade 3 2.30 2.30 2.30 2.20 2.20 3.00 3.00 3.00
Base (polyester) - Grade 3 2.50 2.50 2.50 2.20 2.20 400 3.00 3.00 3.50 400 3.00
Base (composite) - Grade 3 2.30 2.30 2.30 2.20 2.20 400 3.00 3.00 3.50 3.00
Film Cap (fibreglass) - Grade 2 4.00 3.30 3.30 3.30 3.30
Film Cap (polyester) - Grade 2 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Film Cap (composite) - Grade 2 4.00 3.30 3.30 3.30 400 3.00 400 3.30 400 4.00 400 3.00 400 4.00 400
Granular Cap (fibreglass) - Grade 1 4.00 3.30 3.30 3.30 400 3.30
Granular Cap (polyester) - Grade 1 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Granular Cap (composite) - Grade 1 4.00 4.00 3.30 3.30 400 3.00 400 3.00 400 4.00 400 3.00 400 4.00 400

4 SBS 15-year

Table 9.2 SBS-modified Bituminous Membranes: RoofStar 15-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Conventionally Insulated / Uninsulated
2-Ply Systems		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing		 Single-ply
Cap
Mech.
fastened 		Heat-
welded 		Self-
adhered 		Hot-
mopped 		Cold-
adhered 		Puncture
Resist.
Heat-welded / Adhered
Puncture Resistance
Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
Heat-welded / Adhered
Puncture Resistance
As specified
Puncture Resistance
Membrane Type, Reinforcement, Grade mm mm mm mm mm (N) mm (N) mm (N) mm (N) mm (N) mm (N)
Base (fibreglass) - Grade 3 3.00
Base (polyester) - Grade 3 2.50 2.50 2.50 2.50 400 3.00 3.00 3.50 3.00
Base (composite) - Grade 3 2.50 2.50 2.50 2.50 400 3.00 3.00 3.50 3.00
Film Cap (fibreglass) - Grade 2
Film Cap (polyester) - Grade 2 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 4.00 400 3.00 400
Film Cap (composite) - Grade 2 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 4.00 400 3.00 400
Granular Cap (fibreglass) - Grade 1 4.00 4.00 4.00 4.00 400
Granular Cap (polyester) - Grade 1 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 4.00 400 3.00 400
Granular Cap (composite) - Grade 1 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 4.00 400 3.00 400

5 Alternate 1: Single-ply Model

Table 9.1 Single-ply Membranes: RoofStar 5 and 10-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Conventionally Insulated / Uninsulated
Single-Ply Systems		 Ballasted
(Insulated /
Uninsulated)		 PMR
Systems		 Built-in
Gutters		 Roof as a
Platform		 Grade-level
Water-
proofing
Mechanically
Fastened 		Self-adhered Adhered
or
Hot-mopped
(No fleece) 		Adhered
or
Hot-mopped
(Fleece-back) 		Loose-laid Adhered
or
Hot-mopped
(No fleece) 		Adhered
or
Hot-mopped
(Fleece-back) 		Adhered Adhered
or
Hot-mopped
(No fleece) 		Adhered
or
Hot-mopped
(Fleece-back) 		Adhered
or
Hot-mopped
(No fleece) 		Adhered
or
Hot-mopped
(Fleece-back)
Membrane Type, Reinforcement & Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60) 1.524 (60)
EPDM (unreinforced) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.524 (60) 1.524 (60) 1.524 (60) 1.524 (60) 2.794 (110)
TPO 1.143 (45) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60) 1.524 (60) 2.794 (110)
PVC N/A 1.270 (50) 2.667 (105) N/A 1.270 (50) 1.524 (60) 2.667 (105) 1.524 (60) 1.524 (60) 2.667 (105) 1.524 (60) 2.667 (105)


6 Alternate 2: Single-ply Model

Table 9.1 Single-ply Membranes: RoofStar 5 and 10-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Conventionally Insulated / Uninsulated
Single-Ply Systems		 Protected Insulated / Uninsulated
Single-Ply Systems		 Built-in
Gutters
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Ballasted
(Insulated /
Uninsulated) 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Loose-laid Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Adhered
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.143 (45) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
EPDM (unreinforced) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
TPO 1.143 (45) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
PVC 1.270 (50) 1.270 (50) 2.667 (105) 1.270 (50) 1.270 (50) 1.524 (60) 1.524 (60) 1.524 (60)


7 Alternate 3: Single-ply Model

Table 9.1 Single-ply Membranes: RoofStar 5 and 10-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Conventionally Insulated / Uninsulated
Single-Ply Systems		 Protected Insulated / Uninsulated
Single-Ply Systems		 Built-in
Gutters
Ballasted
(Insulated /
Uninsulated) 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Loose-laid Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Adhered
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.143 (45) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
EPDM (unreinforced) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
TPO 1.143 (45) 1.524 (60) 1.143 (45) 2.794 (110) 1.143 (45) 1.143 (45) 1.524 (60) 1.524 (60)
PVC 1.270 (50) 1.270 (50) 2.667 (105) 1.270 (50) 1.270 (50) 1.524 (60) 1.524 (60) 1.524 (60)

8 Single-ply Model (FINAL)

Table 9.1 Single-ply Membranes: RoofStar 5 and 10-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Systems Protected Systems
Conventionally Insulated / Uninsulated Systems Built-in
Gutters 		Ballasted
(Insulated /
Uninsulated) 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Adhered
or
Self-adhered 		Loose-laid Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.143 (45) 1.524 (60) 1.143 (45) 1.143 (45) 1.524 (60)
EPDM (unreinforced) 1.524 (60) 1.143 (45) 2.794 (110) 1.524 (60) 1.143 (45) 1.143 (45) 1.524 (60)
TPO 1.143 (45) 1.524 (60) 1.143 (45) 2.794 (110) 1.524 (60) 1.143 (45) 1.143 (45) 1.524 (60)
PVC 1.270 (50) 1.270 (50) 2.667 (105) 1.524 (60) 1.270 (50) 1.270 (50) 1.524 (60) 1.524 (60)


Table 9.2 Single-ply Membranes: RoofStar 15-Year Guarantee
(Applies to Field and Flashing membranes. All thicknesses shown are in mm.)
*Induction welding subject to the securement requirements in the applicable membrane Standard, Part 3.
Exposed Systems Protected Systems
Conventionally Insulated / Uninsulated Systems Built-in
Gutters 		Ballasted
(Insulated /
Uninsulated) 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Mechanically
Fastened* 		Self-adhered Adhered
or
Hot-mopped
(Smooth) 		Adhered
or
Hot-mopped
(Fleece-backed) 		Adhered
or
Self-adhered 		Loose-laid Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped 		Self-adhered,
Adhered
or
Hot-mopped
Type, Reinforcement, Grade mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils) mm (mils)
EPDM (reinforced) 1.524 (60) 1.524 (60) 1.524 (60) 2.032 (80) 1.524 (60) 2.032 (80)
EPDM (unreinforced) 1.524 (60) 1.524 (60) 2.790 (110) 2.032 (80) 1.524 (60) 2.032 (80)
TPO 1.524 (60) 1.524 (60) 1.524 (60) 2.790 (110) 2.286 (90) 1.524 (60) 2.286 (90)
PVC 1.524 (60) 1.524 (60) 2.667 (105) 2.286 (90) 1.524 (60) 2.286 (90)

9 2-ply Model (FINAL)

Table 9.1 SBS-modified Bituminous Membranes: RoofStar 5 and 10-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Systems Protected Systems
Conventionally Insulated / Uninsulated Systems Built-in
Gutters 		Single-ply
Cap 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Mechanically
fastened
Heat-welded
Self-adhered
Hot-mopped
Adhered
Puncture
Resistance
Heat-welded, Adhered, Self-
adhered
Puncture
Resistance
Adhered
Puncture
Resistance
Heat-welded,
Adhered
Puncture
Resistance
Heat-welded,
Adhered
Puncture
Resistance
Heat-welded, Adhered, Self-
adhered
Puncture
Resistance
Type, Reinforcement, Grade mm mm mm mm mm (N) mm (N) mm (N) mm (N) mm (N) mm (N)
Base (fibreglass) - Grade 3 2.30 2.30 2.30 2.20 2.20 3.00 3.00 3.00
Base (polyester) - Grade 3 2.50 2.50 2.50 2.20 2.20 400 3.00 3.00 3.50 400 3.00
Base (composite) - Grade 3 2.30 2.30 2.30 2.20 2.20 400 3.00 3.00 3.50 3.00
Film Cap (fibreglass) - Grade 2 4.00 3.30 3.30 3.30 3.30
Film Cap (polyester) - Grade 2 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Film Cap (composite) - Grade 2 4.00 3.30 3.30 3.30 400 3.00 400 3.30 400 4.00 400 3.00 400 4.00 400
Granular Cap (fibreglass) - Grade 1 4.00 3.30 3.30 3.30 400 3.30
Granular Cap (polyester) - Grade 1 4.00 3.50 3.50 3.50 400 3.00 400 3.50 400 4.00 400 3.00 400 4.00 400
Granular Cap (composite) - Grade 1 4.00 4.00 3.30 3.30 400 3.00 400 3.00 400 4.00 400 3.00 400 4.00 400


Table 9.2 SBS-modified Bituminous Membranes: RoofStar 15-Year Guarantee
Applies to Field and Flashing membranes. All thicknesses shown are in mm
Exposed Systems Protected Systems
Conventionally Insulated / Uninsulated Systems Built-in
Gutters 		Single-ply
Cap 		PMR
Systems 		Roof as a
Platform 		Grade-level
Water-
proofing
Mechanically
fastened
Heat-welded
Self-adhered
Hot-mopped
Adhered
Puncture
Resistance
Heat-welded, Adhered, Self-
adhered
Puncture
Resistance
Adhered
Puncture
Resistance
Heat-welded,
Adhered
Puncture
Resistance
Heat-welded,
Adhered
Puncture
Resistance
Heat-welded, Adhered, Self-
adhered
Puncture
Resistance
Type, Reinforcement, Grade mm mm mm mm mm (N) mm (N) mm (N) mm (N) mm (N) mm (N)
Base (fibreglass) - Grade 3 3.00
Base (polyester) - Grade 3 2.50 2.50 2.50 2.50 400 3.00 3.00 3.50 3.00
Base (composite) - Grade 3 2.50 2.50 2.50 2.50 400 3.00 3.00 3.50 3.00
Film Cap (fibreglass) - Grade 2
Film Cap (polyester) - Grade 2 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 4.00 400 3.00 400
Film Cap (composite) - Grade 2 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 3.00 400
Granular Cap (fibreglass) - Grade 1 4.00 4.00 4.00 4.00 400
Granular Cap (polyester) - Grade 1 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 3.00 400
Granular Cap (composite) - Grade 1 4.00 4.00 4.00 4.00 400 4.00 400 4.00 400 3.00 400


10 RoofStar 15-Year Guarantee

  1. To qualify for a RoofStar 15-year (Waterproofing Roofs) Guarantee, the following standards apply:
    1. Each Project must be designed and constructed in compliance with both the RoofStar Guarantee Standards and the membrane manufacturer’s 20-year System Warranty standards.
    2. The Contractor must apply to the membrane manufacturer for their 20-year System Warranty standards.
    3. Where enhanced roof system securement is required by the manufacturer, which may exceed the securement required in a Tested Assembly, an Assembly with Proven Past Performance or a custom-engineered securement, the Project must comply with the higher securement requirements.
    4. In addition to the above, other requirements in this Standard apply, which can be summarized (without limitation) as follows:
      1. Roofs must be designed for adequate access to facilitate maintenance (1.3.3).
      2. Materials left in place for partial roof system replacement must be scanned for moisture (1.4.2.2).
      3. All roofs (new construction and replacement roofing) must be built with a minimum slope of 2% (1:50) (2.2.2 and 2.2.3).
      4. All replacement roofing must utilize crickets to enhance drainage around curbs and sleepers (2.2.3).
      5. Curbs and sleepers wider/longer than 1200 mm (48") must incorporate crickets to improve drainage (7.1.2.1).
      6. An insulation overlay is required on all Conventionally Insulated Roof Systems (8.1.1.1).
      7. Only certain membranes will qualify for a RoofStar 15-year Guarantee (9.2).
      8. All drains and overflows require clamping rings, and overflows are required for each roof area (11.1.2.1).
      9. Enhanced penetration flashing requirements (11.1.3.1).
      10. Linear metal flashings must be fabricated from 24-gauge material (13.1.2.1).
Retrieved from "http://rpm.rcabc.org/index.php?title=Miscellaneous_wordings_1&oldid=27272"