Difference between revisions of "TPO Protected Roof Assembly (Typical)"

Latest revision as of 21:34, 27 June 2022

Division D - Construction Details

TPO | Protected Membrane Roof Assembly (Typical) ( Article 1.1.3.1.)

Notice to Reader
Images used in a Construction Detail are representative and not prescriptive, and are not necessarily drawn to scale. They are intended to support the related Standard (Ref. Division A, Article 2.2.1.2.). The reader may link to the related Article in the detail title, or link to the Standard as it relates to a specific element in the detail. All hyperlinks are displayed blue text.

TPO Details

1 WORK INCLUDED

(1) Protection Mat: Provide protection between concrete deck and membrane with installation of manufacturer specified and RGC accepted protection mat or deck overlay boards.
(2) Single-ply Membrane: Installed according to manufacturer's instructions and RoofStar Guarantee Standards.
(3) Adhesive: Proprietary, installed according to manufacturer's instructions, usually brushed, rolled or sprayed.
(4) Membrane Lap: EPDM (thermoset) membrane may be joined using uncured tape or proprietary adhesive.
(5) Fasteners: Install according to manufacturer's instructions (style may vary depending on material type and manufacturer's specification). May vary from drawing.
(6) Membrane Flashing: Adhered according to manufacturer's printed specifications using proprietary adhesive. Must be carried to outside of parapet or minimum 200 mm (8") above finished roof surface. Adhered to primary membrane.
(7) Insulation: Mechanically attached. Installed according to RoofStar Guarantee Standards. See available insulation products in the Division C of this Manual.
(8) Filter Fabric: Metal base flashing required.
(9) Metal Flashing: As required by RoofStar Guarantee Standards.
(10) Ballast: Gravel or concrete paving tiles.
(11) Parapet Flashing: As required by RoofStar Guarantee Standards.

2 RELATED WORK BY OTHERS

(A) Acceptable Deck
(B) Acceptable Parapet Surface: Surface must be smooth, dry and clean. Rough surface must be covered with treated plywood, to be determined by design authority or inspector or as required by manufacturer.
(C) Sloped Wood Blocking

NOTE: See the Standard for additional requirements.

Back to TPO Construction Details

Home

© RCABC 2024
RoofStar^TM is a registered Trademark of the RCABC.
No reproduction of this material, in whole or in part, is lawful without the expressed permission of the RCABC Guarantee Corp.

@@ Line 6: / Line 6: @@
 <big><big>Division D - Construction Details</big></big>
 <hr>
-<big><big><big><big><big>TPO 1.3.1-3 Protected Membrane Roof Assembly (typical)</big></big></big></big></big>
+<big><big><big><big><big>TPO | Protected Membrane Roof Assembly (Typical) ([[TPO_Roof_Systems_Standard#1.1.3.1._Permitted_Roof_Systems | Article 1.1.3.1.]])</big></big></big></big></big>
-{| class="wikitable" | style="color: black; background-color: orange; width: 100%;text-align:center"
+{{Template:Construction Details Header}}
-| colspan="2"  | <big>'''''Notice to Reader'''''</big>
-|-
-| style="color: black; background-color: #ffffcc; width: 100%;text-align:center" | Images used in a Construction Detail are representative and not prescriptive.  Nor are they necessarily drawn to scale. Rather, they are provided to visually convey the requirements of the Standard they represent. Unless otherwise required by the Standard, dimensions, the selection of materials and their application remains the responsibility of the ''Design Authority''.<br><br>The full text of the referenced requirements in the [[TPO Roof Systems Standard | '''Standard''']] may be read by using the <span style="color:#6495ed">'''blue hyperlinks'''</span>
-|}
 <div class="panel panel-success">
 <div class="panel-heading"><big>'''TPO Details'''</big></div>
@@ Line 23: / Line 19: @@
 <div class="col-md-6">
 === WORK INCLUDED ===
-;(1) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOPROTECTION|'''Protection Mat''']]: Provide protection between concrete deck and membrane with installation of manufacturer specified and RoofStar-accepted protection mat or deck overlay boards.
+;(1) [[TPO Roof Systems Standard#PART_9|'''Protection Mat''']]: Provide protection between concrete deck and membrane with installation of manufacturer specified and RGC accepted protection mat or deck overlay boards.
-;(2) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOMEMBRANE|'''Single-ply Membrane''']]: Installed according to manufacturer's instructions and ''RoofStar Guarantee Standards''.
+;(2) [[TPO Roof Systems Standard#PART_9|'''Single-ply Membrane''']]: Installed according to manufacturer's instructions and ''RoofStar Guarantee Standards''.
-;(3) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOADHESIVE|'''Adhesive''']]: Proprietary, installed according to manufacturer's instructions, usually brushed, rolled or sprayed.
+;(3) [[TPO Roof Systems Standard#PART_9|'''Adhesive''']]: Proprietary, installed according to manufacturer's instructions, usually brushed, rolled or sprayed.
-;(4) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOLAP|'''Membrane Lap''']]: Thermoplastic membrane may be welded or chemically bonded.
+;(4) '''Membrane Lap''': EPDM (thermoset) membrane may be joined using uncured tape or proprietary adhesive.
-;(5) '''Fasteners''': Install according to manufacturer's instructions (may vary from drawing).
+;(5) '''Fasteners''': Install according to manufacturer's instructions (style may vary depending on material type and manufacturer's specification).  May vary from drawing.
-;(6) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOSTRIPPING|'''Membrane Flashing''']]: Adhered according to manufacturer's printed specifications using proprietary adhesive. Must be carried to outside of parapet or minimum 200 mm (8") above finished roof surface. Welded or adhered to primary membrane depending on membrane type.
+;(6) [[TPO Roof Systems Standard#PART_10|'''Membrane Flashing''']]: Adhered according to manufacturer's printed specifications using proprietary adhesive. Must be carried to outside of parapet or minimum 200 mm (8") above finished roof surface. Adhered to primary membrane.
-;(7) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOINSULATION|'''Insulation''']]: Mechanically fastened where deck type permits, or fully adhered (as illustrated). Installed according to ''RoofStar Guarantee Standards''. See available insulation products in the [[Roof Deck Insulation|'''Accepted Materials''']] section of this Manual.
+;(7) [[TPO Roof Systems Standard#PART_7|'''Insulation''']]: Mechanically attached. Installed according to ''RoofStar Guarantee Standards''. See available insulation products in the [[Division C | Division C]] of this Manual.
-;(8) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOFILTER|'''Filter Fabric''']]: Metal [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOMETALBASE|'''Base Flashing''']] required.
+;(8) [[TPO Roof Systems Standard#PART_14|'''Filter Fabric''']]:  Metal base flashing required.
-;(9) [[RoofStar Guarantee Standards for TPO Membrane Systems#METALCAP-TPO|'''Metal Flashing''']]: As required by RoofStar Guarantee Standards.
+;(9) [[TPO Roof Systems Standard#PART_13|'''Metal Flashing''']]: As required by ''RoofStar Guarantee Standards''.
-;(10) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOBALLAST|'''Ballast''']]: Gravel or concrete paving tiles.
+;(10) [[TPO Roof Systems Standard#PART_3|'''Ballast''']]: Gravel or concrete paving tiles.
-;(11) [[RoofStar Guarantee Standards for TPO Membrane Systems#METALCAP-TPO|'''Parapet Flashing''']]: As required by RoofStar Guarantee Standards.
+;(11) [[TPO Roof Systems Standard#PART_13|'''Parapet Flashing''']]: As required by ''RoofStar Guarantee Standards''.
 <hr>
 === RELATED WORK BY OTHERS ===
-;(A) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPODECKS|'''Acceptable Deck''']]
+;(A) [[TPO Roof Systems Standard#PART_2|'''Acceptable Deck''']]
-;(B) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOWALLSUB|'''Acceptable Parapet Surface''']]: Surface must be smooth, dry and clean. Rough surface must be covered with treated plywood, to be determined by design authority or inspector or as required by manufacturer.
+;(B) [[TPO Roof Systems Standard#PART_10|'''Acceptable Parapet Surface''']]: Surface must be smooth, dry and clean. Rough surface must be covered with treated plywood, to be determined by design authority or inspector or as required by manufacturer.
-;(C) [[RoofStar Guarantee Standards for TPO Membrane Systems#TPOWOODBLOCKING|'''Sloped Wood Blocking''']]
+;(C) [[TPO Roof Systems Standard#PART_13|'''Sloped Wood Blocking''']]
 </div><!-- COL-6-MD -->
 </div><!-- PANEL BODY -->

Difference between revisions of "TPO Protected Roof Assembly (Typical)"

Difference between revisions of "TPO Protected Roof Assembly (Typical)"

Latest revision as of 21:34, 27 June 2022

1 WORK INCLUDED

2 RELATED WORK BY OTHERS

3 Accept Terms Of Use