Template:Tested Assembly tables (Using the Tables)

Using the TablesUsing the Tables

NOTICE to READER

Before you use these tables, make sure you know the wind load requirements for the roof under design or construction. You can find guidance in Part 3 SECURING the ROOF ASSEMBLY of the membrane system that is specified. Specified Wind Loads for the three principal roof zones may be calculated either by using the formulae in the British Columbia Building Code, 4.1.7 Wind Loads, or by using the National Research Council's online tool, Wind-RCI online wind calculator.

Table Structure and Organization

The tables on the adjacent tabs display data drawn from, and links to, Tested Assembly Reports listed by the membrane type shown on the tab heading. All test reports are downloadable from the "Test Report" column, and are catalogued under a RoofStar numbering system that may differ from the number designation on the report. Dynamic Wind Uplift (DUR) values are shown in columns near the left side of the tables. Only the DUR and Manufacturer columns are sortable; to sort a column, click the column heading. Click on any drop-down button to try the demo table below.

Tested Assembly Report Data					Primary Materials			Other System Materials & Deck
Manufacturer	Dynamic Uplift Resistance		Roof Assembly Summary	Test Report	Cap Membrane	Base Membrane	Plies	Insulation Overlay	Insulation	Deck Overlay	Deck Type
Manufacturer	kPa	Psf	Roof Assembly Summary	Test Report	Cap Membrane	Base Membrane	Plies	Insulation Overlay	Insulation	Deck Overlay	Deck Type
Manufacturer	-1.9	-40	EXAMPLE ONLY Cap membrane: application/securement method Base membrane: mechanically fastened Insulation overlay: (optional) various securement options Insulation (top layer): mechanically fastened Insulation (bottom layer): N/A Air/Vapour control layer: various securement options Deck overlay (thermal barrier): various securement options Roof deck	Report link 1-A	Membrane Option 1 Membrane Option 2 Membrane Option 3	Membrane Option 1 Membrane Option 2 Membrane Option 3	1, 2 or 3	Insulation overlay Option 1 Insulation overlay Option 2 Insulation overlay Option 3	Insulation Option 1 Insulation Option 2 Insulation Option 3	Deck overlay Option 1 Deck overlay Option 2 Deck overlay Option 3	Deck type

Each row displays one test for a particular system of securement. That means that the DUR derived for that test is based on a particular pattern of fasteners or adhesive application. Most assemblies were tested with one system of securement, but some were tested with as many as four. When this is the case, the same report number will be displayed with test report names such as [Manufacturer X] MARS 1-A and [Manufacturer X] MARS 1-B. Read the test report details to see what was changed in the securement system that affected the DUR for the assembly.

Every table displays Tested Assembly report data in easy-to-read rows with drop-down buttons that display key information for each assembly (see the working example above). When the Tested Assembly uses a membrane with 2 or more plies, each membrane and its options is listed in separate columns.

Note that some tests were conducted without one or more of these constituent components and may list those materials as "optional". When a material category such as "insulation overlay" is absent from the test, the drop-down menu will indicate its absence with "N/A" or as "optional". Occasionally, a missing material poses a conflict with the RoofStar Guarantee Standards. When the conflict is obvious, the Roof Assembly Summary will normally flag this with a note at the bottom of the list. Notwithstanding these notes, the reader is responsible to understand and apply the RoofStar Guarantee Standards regardless of the Tested Assembly report (see below under Tested Assemblies and RoofStar Guarantee Standards).

The Roof Assembly Summary provides a quick overview of how the roof assembly is secured. This feature of the tables will be especially helpful when searching for a suitable PARS assembly, because the placement of mechanical fasteners within an assembly can vary widely. Note, however, that the summaries do not list sizes, types or spacing of specific adhesives or fasteners; these details must be obtained from a careful reading of the Tested Assembly report.