Difference between revisions of "Insulation Joints and Overlays"

Jump to: navigation, search

Difference between revisions of "Insulation Joints and Overlays"

(Insulation Joint Tape)
(Insulation Joint Tape)
Line 23: Line 23:
 
==== Insulation Joint Tape ====
 
==== Insulation Joint Tape ====
 
Where <i>RGC Guarantee Standards</i> or the roof system specification calls for
 
Where <i>RGC Guarantee Standards</i> or the roof system specification calls for
taping fibreboard or insulation joints, consult the [[Insulation Joint Tape|list of Accepted Materials]] in the [[:Section:C. Accepted Materials|C. Accepted Materials]] section of this Manual:
+
taping fibreboard or insulation joints, consult the list of [[Insulation Joint Tape|Accepted Materials]] in the [[:Section:C. Accepted Materials|C. Accepted Materials]] section of this Manual:
  
 
==== Asphalt and Paraffin-Impregnated / Coated Fibreboard Roof Insulation and Insulation Overlay Board ====
 
==== Asphalt and Paraffin-Impregnated / Coated Fibreboard Roof Insulation and Insulation Overlay Board ====

Revision as of 16:28, 20 June 2016

1 General

Insulation overlays are used to separate the roof membrane from the primary insulation, usually for one of two reasons:
  • to prevent the insulation from affecting the performance of the roof membrane
  • to prevent the roof membrane and / or the method of application from affecting the insulation

The insulation can affect the performance of the roof membrane in the following ways:

  • the insulation may be incompatible with the membrane, resulting in a loss of physical properties
  • different coefficients of thermal expansion may result in membrane splits / cracks.

The roof membrane and / or the method of application can affect the insulation in the following ways:

  • the insulation may not be capable of withstanding asphalt application temperatures and may “burn-out”
  • some insulations will not accommodate direct torch-applied membranes
  • insulations that are too “soft” may result in delamination or damage to the membrane or insulation when exposed to heavy loads or traffic
  • the solvents and adhesives used for flexible membranes may adversely affect the insulation.


NOTE: All hot asphalt-adhered asphaltic membranes (built-up roofing, modified bitumen, etc.) require an insulation overlay over heat sensitive insulations and heat insensitive foamed insulation. RGC Guarantee Standards for heat sensitive insulations require a two-layer overlay board for a five (5) or ten (10) year Guarantee. RGC requires the use of a two-layer overlay board over heat sensitive insulations in all cases, and also requires a single-layer overlay board application over heat insensitive insulations for all hot asphalt-adhered membranes. For single-ply, non-asphaltic membrane roofing systems, the membrane manufacturer should be consulted for proprietary options.


1.1 Insulation Joint Tape

Where RGC Guarantee Standards or the roof system specification calls for taping fibreboard or insulation joints, consult the list of Accepted Materials in the C. Accepted Materials section of this Manual:

1.2 Asphalt and Paraffin-Impregnated / Coated Fibreboard Roof Insulation and Insulation Overlay Board

BUILDING PRODUCTS OF CANADA CORP.
  • Petroleum Paraffin-Impregnated Asphalt Coated fibreboard conforming to CAN / ULC - S706-02
IKO INDUSTRIES INC.
  • Asphalt-Impregnated Coated fibreboard conforming to CAN / ULC - S706-02
LOUISEVILLE SPECIALTY PRODUCTS INC.
  • Asphalt Coated (6 sides) Natural Fibreboard conforming to CAN / ULC - S706-02
  • Asphalt and Wax Impregnated Fibreboard conforming to CAN / ULC - S706-02
  • Asphalt and Wax Impregnated High Density Fibreboard conforming to CAN / ULC - S706-02
  • Securpan Asphalt coated (one side) Fire Resistant Fibreboard conforming to CAN / ULC - S706-02

1.3 Proprietary Overlay Boards

JOHNS MANSVILLE CORPORATION
  • ½" (13 mm) Retro-Fit™ Board Perlitic Roof Board
  • Invinsa™ Roof Board
HAL INDUSTRIES INC.
  • Asphalt Overlay Board
HENRY COMPANY CANADA.
  • Asphalt Overlay Board
IKO INDUSTRIES LTD.
  • Asphalt Overlay Board
SOPREMA INC.
  • Asphalt Overlay Board
  • Fire Resistant Wood Fibreboard with a Factory Applied Base Sheet
  • Xpress Board Mineral Wool Fibre Insulation with a Factory Applied Base Sheet
  • Soprarock MD
  • Soprarock MD+
GEORGIA PACIFIC CANADA LTD.
  • Gypsum Overlay Board
FIRESTONE BUILDING PRODUCTS
  • Isogard HD Cover Board
POSI-SLOPE WESTERN
  • MF - Protect Board Composite
ROXUL
  • MonoBoard
  • MonoBoard+
SECUREROCK
  • Gypsum - Fibre Roof Board
  • Glass - Mat Roof Board
CARLISLE SYNTEC.
  • Secure Shield HD Plus Cover Board

2 MANUFACTURERS

2.1 JOHNS MANVILLE CORPORATION

Manufacturer: JOHNS MANVILLE CORPORATION

Contact Address: See Membership List, Section 1

Product Group: PERLITIC ROOF INSULATION - RETRO-FIT BOARD

Country of Origin: USA

Country of Manufacture: USA

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

Retro-Fit Board is a perlite-based utility board for use as a divorcing layer in reroofing and in new construction as a top layer in a multi-layer insulation system.

Half-inch Retro-Fit Board is a high density board made of expanded perlite and cellulosic fibres. It serves as an upgrade for wood fibre utility roofing products. The perlite particles are subjected to intense heat, which causes them to expand approximately fifteen times their original size.

The top surface is sealed with Top-Loc coating to ensure good attachment in bituminous applications. The minimum recycled content is 35% by weight.

Retro-Fit Board Insulation / Overlay

Thermal Resistance: RSI = .23 / 13 mm (R value = 1.32 / 1/2 inch)
Uses 13 mm (1/2") Retro-fit Board is a perlite-based utility board for use as a divorcing layer in reroofing and in new construction as a top layer in a multi-layer insulation system. It is not recommended for use directly over steel decks. It may be applied using hot bitumen and / or mechanical fasteners. It may be used as a primary or overlayment board.
Standards:
  • CSA A284-1976
  • CAN / CGSB 51.10-92
  • ASTM C 728
  • Factory Mutual Approved
  • Underwriters Laboratories Canada
Compressive Strength: CSA A284-1976 37 psi
Density: CSA A284-1976 13 pcf
Standard Sizes 0.6 m x 1.2 m
(24" x 48")
1.2 m x 1.2 m
(48" x 48")
1.2 m x 2.4 m
(48" x 96")
Thicknesses: 13 mm (½")

Manufacturer: JOHNS MANVILLE CORPORATION

Contact Address: See Membership List, Section 1

Product Group: INVINSA ROOF BOARD

Country of Origin: USA

Country of Manufacture: USA

Year First Installed:

  • Canada:1993
  • USA:1989
  • Outside North America:1995

DESCRIPTION

Invinsa™ Roof Board is a resilient, lightweight roof board designed as an integral component of the roof system, providing a protective layer for the insulation, while working with the membrane above to ensure maximum performance and longevity.

This patent-pending, high-density polyisocyanurate technology is bonded in-line to mineral-surfaced, fiber glass reinforced facers. In single ply and bituminous cold-applied and self-adhered roof systems, Invinsa enhances fire, water and hail resistance, and it will not support mold growth.

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.


Code Approvals and Testing

Invinsa has been tested according to the requirements of ASTM C 209, C 473, C 518, C 1289, D 1037, D 1621, D 2126, D 3273 and E 96. It has been classified by Underwriters Laboratories Inc. as an approved cover board for certain Class “A” fire-rated roof constructions. It can be used in numerous FM Global 1A-90 or above roof constructions.


Use

Invinsa optimizes roof system performance in new, re-cover and re-roof applications. It can be installed over an existing roof to increase the integrity of the new roof. The coated fiber glass facers provide strong, smooth surfaces suitable for mechanically attached or fully adhered membranes, without the need for priming.


Advantages

  • Invinsa’s light weight offers labour and installation efficiencies and allows more options for situations where the overall weight is a concern.
  • Light weight also means easy hoisting, staging and manoeuvring around the roof.
  • High impact and flexural strength provide increased resistance to damage from various sources, including but not limited to hail, foot traffic, construction loads and normal roof maintenance.
  • Low water absorption characteristics offer performance benefits in diverse environments.
  • JM Invinsa roof board is user friendly, allowing easy and efficient scoring, cutting and snapping, which permits fast, tight fabrication around roof penetrations.
  • Board composition provides a low dust environment and smooth surface for better adhesion.
  • Flexibility means less breakage during handling, and in re-cover applications it allows Invinsa to accommodate minor irregularities in existing roofs.


Typical Physical Properties

English Units Metric Units ASTM Test Method
Thickness (nominal) 1/4 in. 6.4 mm -
Width 4ft 1.22 m -
Length, Standard 4ft 1.22 m -
8ft 2.44 m -
Flexural Strength 2000 psi
28 lbf
13,790 kPa
4.9 kN/m
D 1037
D 1037
Dimensional Stability <0.6% <0.6% D 2126
Moisture Vapor Permeance <1 perm <57.5 ng/Pa•s•m² E 96
R-Value 1.0 (hr•ft²•°F)/Btu 0.18 m²•ºC/W C 518
Water Absorption (max) 2.6% 2.6% C 209
Compressive Strength (min) 150 psi
21,600 psf
1034 kPa
1,034,200 Pa
D 1621
Surface Water Absorption Mold Resistance <1 gram Pass <1 gram Pass C 473
D 3273
Weight per 4' x 8' Sheet (1.22 m x 2.44 m) 12 ± 2 lbs 5.4 ± 0.9 kgs -
Weight per Pallet (4' x 8' sheets) 370 lbs 167 kg -
Sheets per Pallet
4' x 8' (1.22 m x 2.44 m)
4' x 4' (1.22 m x 1.22 m)
30 Sheets
30 Sheets
30 Sheets
30 Sheets
-

2.2 HAL INDUSTRIES INC.

Manufacturer: HAL INDUSTRIES INC.

Contact Address: See Membership List, Section 1

Product Group: ASPHALT OVERLAY BOARD

Country of Origin: Canada (B.C.)

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

PERMA-BOARD is a semi-rigid waterproof sheet with a rubberized asphalt core sandwiched within two layers of fibreglass reinforcement. Available with a smooth poly film surface finish or a sanded finish. PERMA-BOARD is compatible with all asphalt roofing systems and is unaffected by moisture and will not rot.


PERMA-BOARD Asphalt Base Board / Overlay

Uses: PERMA-BOARD is designed to be used as an overlay to insulation and as a base for modified, built-up and single ply membranes. Elastomeric roofing membranes or built-up roofing may be heat welded or hot mopped directly to PERMA-BOARD, creating a thick waterproofing layer. The asphalt board becomes an integral part of the roof membrane making it stronger and more puncture resistant than it would otherwise be.
Performance Properties: Tensile Strength @ 23°C 590 N / 25 mm (135 lb. / in.)
Puncture Strength @ 23°C > 450 N / 1 cm. sq.
Softening Point Temperature 105°C (221°F)
Maximum Water Absorption 0.5%
Physical Properties: Dimensions 1 m x 2 m (40" x 80" nominal size)
Thickness 4.5 mm (3/16") nominal
Weight 10.4 Kg (23 lb.) Per sheet nominal
Reinforcement Two plies, fibreglass mat

2.3 LOUISEVILLE SPECIALTY PRODUCTS INC.

Manufacturer: LOUISEVILLE SPECIALTY PRODUCTS INC.

Contact Address: See Membership List, Section 1

Product Group: FIRE RESISTANT WOOD FIBREBOARD - COATED WITH ASPHALT - SECURTORCH

Country of Origin: Canada (B.C.)


DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.


SECURTORCH

Securtorch is a safe and unique fireboard roofing insulation coated with a thick layer of asphalt covered with a thermofusible protective layer. Its core has been thoroughly treated to provide Class A fire resistance.

Thermal Resistance RSI value = 0.27 / 12.5 mm (1/2") [R Value = 1.5 / 25 mm (1")]
Standard sizes Panel size: 1.22 m x 1.22 m (4’ x 4’)
With thickness of: 12.5 mm (1/2")
Coverage 16 ft²
Properties Standards Results
Density (specific mass) ASTM D-1037 14.5 lb / ft3 (232 kg / m3
Transverse load ASTM C-209 10.6 lb (47N)
Tensile strength perpendicular to surface ASTM C-209 761 lb / ft2 (min)
36.5 kPa (min)
Water absorption ASTM C-209 3.5%
Linear expansion ASTM C-209 0.10%
Resistance to compression
(10% deformation)
ASTM C-165 45 lb / in2 (min)
Resistance to compression
(25% deformation)
ASTM C-165 80 lb / in2 (min)
R-factor (1/2 inch) ASTM C-518 1.5
Flame spread ULC-S-102
ULC - S - 102.2
15
20
Smoke development ULC-S-12 15
Dimensions1.22 m x 1.22m (4' x 4' sheets)
Thickness12.5 mm (½")
StandardsCAN / CSA - A247-M86 and ULC
Note: tests conducted without the asphalt layer.

2.4 BAKOR INC.

Manufacturer: BAKOR INC.

Contact Address: See Membership List, Section 1

Product Group: ASPHALT OVERLAY BOARD

Country of Origin: Canada (Ontario)

Country of Manufacture: Canada


DESCRIPTION

The roofing assembly / material information published in the RGC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

RE-COVER BOARD is a pre-fabricated board with a mineral filled, high melt point asphalt core, between non-woven glass fibre mats. One side of the product has a poly film surface and the other side has a glass mat surface. RE-COVER BOARD is stable, will not curl, highly resistant to moisture, and is compatible with all asphalt and modified asphalt roofing systems.

RE-COVER BOARD Asphalt Overlay Board:

Uses: RE-COVER BOARD is designed for use with BUR and modified bitumen membranes. It is used as an overlay board for roof insulations and as a deck overlay to provide a strong, stable, and moisture resistant surface to either mop, cold adhesive, or torch apply asphalt membranes to.
Physical Properties Dimensions 1.3 m x 1.6 m or 1.3 m x 2.6 m x 6 mm
(4' x 5' or 4' x 8' x 1/4")
Thickness 4.5 mm (3/16") and 6 mm (1/4")
Weight 6 mm (1/4"); 9.76 kg / sq. m (1.95 lb / sq. ft.)
Surfacing Top: Polyethylene Film over Glass Fibre Mat
Bottom: Glass Fibre Mat
Water Absorption CAN / CSA A247M - 0.14%
Tensile Strength CAN / CSA A247M
* md --- 7.21 MPa (1046 psi)
* xd --- 5.7 MPa (822 psi)
Linear Expansion CAN / CSA A247M --- 0.13% @ 100% RH
Density 1748 kg / cu. m (91 lb. / cu. ft.)
Compression Strength @ 10% deformation -- 10.34 MPa (1500 psi)

2.5 IKO INDUSTRIES LTD.

Manufacturer: IKO INDUSTRIES LTD.

Contact Address: See Membership List, Section 1

Product Group: ASPHALT OVERLAY BOARD

Country of Origin: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

PROTECTOBOARD consists of a mineral-fortified asphaltic core between two layers of high strength glass fibre mat. Surfaced with a solution which allows the product to remain smooth, ideally suited to applications in torched, mopped or cold process assemblies.

PROTECTOBOARD has exceptional compressive strength and puncture resistance and can be used as an overlay, base board, in modified and built up roofing assemblies.

This product can also be applied in the waterproofing assembly of bridge and podium decks, vertical walls and parking garages.

PROTECTOBOARD ASPHALT BASE BOARD / OVERLAY

Physical Properties:

Characteristics Units Typical Value Test Method Standard Limits
Weight Protectoboard:
1.22 m x 1.52 m (4 ft x 5 ft)
1.22 m x 2.44 m (4 ft x 8 ft)
kg (lb) 13.6 (30)
21.8 (48)
Thickness 4.5 mm (3/16"): mm (in) 4.5 (.18) - +/-10%
Width mm (ft) 1220 (4) - +/-6 (1/4")
Length mm (ft) 1520 & 2440
(5 & 8)
- +/-6 (1/4")
Mat Weight g / sq.m
(lb / 100 sq.ft)
2 @ 90
(2 @ 1.8)
ASTM D228 -
Moisture Content % <1 ASTM D146 MAX: 5
Asphalt Content % 45-55 ASTM D147 -
Moisture Absorption % 2 DSM #9.90.60 MAX: 5
Dimensional Stability % <0.2 ASTM D1204 MAX: 10

Manufacturer: IKO INDUSTRIES LTD.

Contact Address: See Membership List, Section 1

Product Group:

FIRE RESISTANT WOOD FIBREBOARD WITH A

FACTORY APPLIED BASE SHEET

Country of Origin: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

ROOFCRAFT BASE FR AND ROOFCRAFT BASE FR 180

Roofcraft Base FR is made form a 12.5 mm (1/2") high-density fibreboard. A film-surfaced SBS Modified membrane is laminated t the top of the fibreboard. The selvage edge becomes self-adhering once the release film is removed. Roofcraft Base FR may be applied by mechanical attachment, hot asphalt, or cold process adhesive. It is fire resistant and the fibreboard content of this product conforms to the CSA A247 Standard.

Physical Properties Dimensions 0.91 m x 2.44 m (3' x 8')
Thickness 12.5 mm (1/2")
Weight 5.79 kg / sq. m (1.18 lb / sq. ft.)
Reinforcing Glass Fibre Mat
Surfacing Thermofusible Plastic Film

2.6 SOPREMA INC.

Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: ASPHALT OVERLAY BOARD

Country of Origin: Canada (Ontario)

Country of Manufacture: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

SOPRABOARD is a multi-ply, semi-rigid asphaltic roofing substrate board composed of a mineral fortified asphaltic core formed between two asphaltic saturated fibreglass liners.

SOPRABOARD is compatible with modified bitumen and BUR roofing systems. Modified bitumen roofing systems can be torched directly to the board surface. Should not be left exposed.

SOPRABOARD Asphalt Overlay Board:

Uses: SOPRABOARD is designed to be used as a substrate material in flat or low-slope roofing. It can be installed over word decks or rigid insulation as an overlay board.
Physical Properties: Dimensions 1.2 m x 1.5 m (4' x 5')
1.2 m x 2.4 m (4' x 8')
Thickness 4.5 mm (3/16") and 6.3 mm (1/4")
Weight 6 mm (1/4"); 9.76 kg / sq. m (1.95 lb / sq. ft.)
Surfacing Glass Fibre Mat

Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: FIRE RESISTANT WOOD FIBREBOARD WITH A FACTORY APPLIED BASE SHEET

Country of Origin: Canada

Country of Manufacture: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

SOPRABASE FR and SOPRABASE 180 FR

SOPRABASE FR (glass fleece reinforcement) and SOPRABASE 180 FR (non-woven polyester reinforcement) are high strength wood fibre composite boards constructed with a factory applied base sheet on the top surface. The wood fibreboard is impregnated with fire retardant (with a flame spread rating not more than 25 on any exposed surface). The base sheet, laminated to the substrate board with an adhesive, is offset from the panel to provide shiplap on two adjacent edges; other edges are square. A thermofusible plastic film covers the top face.

SOPRABASE FR and SOPRABASE 180 FR can be mechanically fastened, bonded with hot bitumen or cold adhesives.

Thermal Resistance: RSI value = 0.20 / 25 mm (1") [R Value = 1.1 / 25 mm (1")]
Standard Sizes: Membrane size: 1 m x 2.69 m (39" x 106")
Panel size: 0.91 m x 2.59 m (36" x 102")
with thicknesses of: 12 mm (15/32") [2.2 mm membrane included]
Weight: Soprabase FR: 13.6 kg
Soprabase 180 FR: 13.0 kg
Coverage: 25 ft² (4 panels / sq.)

Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: XPRESS BOARD HD

Country of Origin: Canada

Country of Manufacture: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

Xpress Board HD is a mineral wool fibre insulation made from basalt rock and steel slag with a factory-applied polyester reinforced SBS modified bitumen base sheet on the top surface with a thermofusible plastic film on a sanded surface. The base sheet, laminated to the substrate board with an adhesive, is offset from the board on two adjacent edges (1" on one end and 3 3/8" on one side) to provide shiplap; other edges are square. To ensure a secure installation, Xpress Board HD is made up of a patented duo selvege edge unique to Soprema (70% self-adhesive and 30% thermofusible). Its self-adhesive component protects combustible surfaces and its thermofusible properties provide an efficient seal. End laps can be aligned then sealed by heat welding a membrane strip.

Xpress Board HD products are available in various thicknesses. Each board is folded in two for easy shipping and handling. It can be mechanically fastened or bonded with a full coat of hot asphalt.


Xpress Board HD can be used for the following applications:

  • As a thermal and vapour barrier directly on decks.
  • As insulation and base sheet flashing on upstands.
  • As insulation and overlay board on all types of insulation.
  • As insulation and base sheet in roof assemblies.
  • As a recovery board and base sheet on existing roofing.

PROPERTIES:

Standards Xpress Board HD
Board dimensions - 0.91 x 4.88 (3 x 16 ft)
Membrane Dimensions - 1 x 4.98
Coverage (m2) - 4.5 (48 ft2)
Total Thickness (mm) - 12 (1/2") up to 125 (5")
R value (per 25 mm) - 4
Membrane reinforcement - Polyester
Breaking Strength, MD / XD (kN / m) CAN / CGSG-37.56M. 10.9 / 6.8
9th draft
Ultimate Elongation, MD / XD (%) CAN / CGSB-37.56M. 51 / 61
9th draft
Tear Strength, MD / XD (N) ASTM D4073 500 / 275
Cold bending (°C) - initial CAN / CGSB-37.56M. -30
90 days at 70°C 9th draft -30

Note: Xpress Board HD products of 2" and thicker are only available in 3 x 8 ft.

Soprema Inc. may modify the composition of its products without prior notice. Consequently orders will be filled according to the latest specification.


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: XPRESS EPS

Country of Origin: Canada

Country of Manufacture: Canada


DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications The preparation of a detailed specification is the responsibility of the design authority.

Xpress EPS overlay board is expanded polystyrene factory laminated with adhesive to a mineral wool fibre insulation made from basalt rock and steel slag with a factory-applied polyester reinforced SBS modified bitumen base sheet laminated on the top surface with a thermofusible plastic film or a sanded surface The base sheet is offset from the board on two adjacent edges (1" on end and 3 3/8" on side) to provide shiplap, other edges are square To ensure a secure installation, Xpress EPS is made with the patented DUO- SELVEDGE, a lap unique to Soprema (70% self- adhesive and 30% thermofusible) Its self-adhesive component protects combustible surfaces and its thermofusible properties provide an efficient seal End laps can be aligned then sealed by heat welding a minimum 12" wide membrane reinforcing strip.

Xpress EPS is available 1m x 4.9m (39" x 16') and in various thicknesses Each board is folded in two for easy shipping and handling It can be mechanically fastened or bonded with DUOTACK adhesive.

Xpress EPS is an overlay board and base sheet combined, adding various thermal resistance values to primary insulation.

MEMBRANE PROPERTIES TEST METHOD TYPICAL RESULTS
Reinforcement Non-woven Polyester
Breaking Strength MD/XD CAN/CGSB37.6-M (kN/m) 17.0/12.5
Ultimate Elongation CAN/CGSB37.56-M (%) 60/65
Tear Strength MD/XD ASTM D5601 (N) 60
Cold Bend -initial CAN/CGSB37.56-M - 30°C
- 90 days @ 70°C CAN/CGSB37.56-M - 30°C
MINERAL WOOL PROPERTIES TEST METHOD TYPICAL RESULTS
Thermal Resistance R-4/inch (25mm) thickness
Surface Burning Characteristics ASTM E84 Flame Spread - 3, Smoke Dev - 0
Water Absorption ASTM C209 (%) <1.1
Compressive Properties ASTM C87l/C665 (psi) 14
Linear Shrinkage ASTM C356 (%) 0.19
EPS PROPERTIES TEST METHOD TYPICAL RESULTS
Thermal Resistance ASTM C518 R3.5/inch (25mm) thickness
Dimensional Stability ASTM D2126 (%) 0.5
Compressive Strength ASTM Dl621 (kPa/psi) 70/10
Tensile Strength ASTM Dl623 (kPa/psi) 140/20
Water Absorption ASTM D2842 (% by volume) 6
Water Vapour Permeanee ASTM C355 (ng/Pa.s.m2) 300 - 4 perm

Soprema Inc. may modify the composition of its products without prior notice consequently orders will be filled according to the latest specification.


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: XPRESS ISO

Country of Origin: Canada

Country of Manufacture: Canada


DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

Xpress ISO overlay board is a polyisocyanurate insulation board laminated with adhesive to a mineral wool fibre insulation made from basalt rock and steel slag with a factory-applied polyester reinforced SBS modified bitumen base sheet on the top surface with a thermofusible plastic film or a sanded surface. The base sheet is offset from the board on two adjacent edges (1" on end and 3 3/8" on side) to provide shiplap, other edges are square. To ensure a secure installation, Xpress ISO is made with the patented DUO-SELVEDGE, a lap unique to Soprema (70% self-adhesive and 30% thermofusible). Its self-adhesive component protects combustible surfaces and its thermofusible properties provide an efficient seal end laps can be aligned then sealed by heat welding a minimum 12" wide membrane reinforcing strip.

Xpress ISO is available in lm x 4.9m (39" x 16') up to 89 mm (3½") thick and lm x 2.4m (39" x 8') from 89 mm to 114 mm (3½" - 4½") thick. The larger boards are folded in two for easy shipping and handling. It can be mechanically fastened in seam with SOPRAFIX FASTENERS and PLATES, bonded with COLTACK or DUOTACK adhesive, or bonded in hot asphalt.

XPRESS ISO is an overlay board and base sheet combined, adding various thermal resistance values to primary insulation used as the overlay and base sheet combined.

MEMBRANE PROPERTIES TEST METHOD TYPICAL RESULTS
Reinforcement Non-woven Polyester
Breaking Strength MD/XD) CAN/CGSB 37.56-M (kN/m) 17.0/12.5
Ultimate Elongation CAN/CGSB 37.56-M (%) 60/65
Tear Strength ASTM D5601 (N) 60
Cold Bend - Initial CAN/CGSB 37.56-M -30°C
Cold Bend - -90 days @ 70°C CAN/CGSB 37.56-M -30°C
MINERAL WOOL PROPERTIES TEST METHOD TYPICAL RESULTS
Thermal Resistance R-4/inch (25mm) thickness
Surface Burning Characteristics ASTM E84 Flame Spread - 3, Smoke Dev - 0
Water Absorption ASTM C209 (%) <1.1
Compressive Properties ASTM C871/C665 (psi) 14
Linear Shrinkage ASTM C356 (%) 0.19
POLYISO PROPERTIES TEST METHOD TYPICAL RESULTS
Thermal Resistance ASTM C518 1" - RSI-l.06 (R-6)
1.5" - RSI-1.58 (R-9)
2" - RSI-2.13 (R12 1)
Dimensional Stability ASTM D2126 (%) <2
Compressive Strength ASTM D1621 (kPa/psm) 138/20
Product Density ASTM D1622 (kg/m3) 32 (2.0 pcf)
Water Absorption ASTM C209 (% by volume) <1
Water Vapour Permeance ASTM E96 (ng/pa.s.m2) 57.5 (<1 Perm)

Soprema Inc. may modify the composition of its products without prior notice Consequently orders will be filled according to the latest specification.


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: SOPRAROCK MD and SOPRAROCK MD PLUS

Country of Origin: Canada

Country of Manufacture: Canada

Detailed information is not available at this time


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: SOPRAROCK DD and SOPRAROCK DD PLUS

Country of Origin: Canada

Country of Manufacture: Canada

Detailed information is not available at this time


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: SOPRASMART BOARD 180

Country of Origin: Canada

Country of Manufacture: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer's data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

Soprasmart Board 180 is a high density composite panel composed of a non-woven polyester reinforced membrane, available with either a thermofusible or sanded surface, laminated on a semi-rigid asphaltic board (Sopraboard). The base sheet is offset from the board on two adjacent edges (1 inch on one end and 3-1/2 inches on 1 side) to provide shiplap; other edges are square. To ensure a secure installation, the side lap is made with a patented DUO-SELVEDGE unique to Soprema (60% self-adhesive and 40% thermofusible). Its self-adhesive component protects combustible surfaces and its thermofusible properties provide an efficient seal. End laps can be aligned then sealed by heat welding a minimum 12" wide membrane reinforcing strip centered over the end lap. Soprasmart Board 180 can be mechanically fastened, adhered with Duotack adhesive, or with a full coat of hot bitumen.


Soprasmart Board 180 can be used for the following applications:

  • an overlay board and base sheet on all types of insulation
  • a recovery board and base sheet on existing roofing
  • an overlay board and base sheet on wood decks

PROPERTIES:

Standards Soprasmart Board 180
Board Dimensions - 0.91m x 2.44m (3 x 8 ft)
Total Thickness (mm) - 7 mm (9/32")
Membrane Reinforcement - non-woven polyester
Total Weight - 9.5kg/m2 (1.99lb/sf)
Top Surface - film or sand
Underface - asphaltic board
Membrane Thickness - 2.2mm (86.6 mils)
Breaking Strength, MD / XD 37GP56M 17.0 / 12.5 kN/m
Ultimate Elongation, MD / XD 37GP56M 60/65%
Tear Strength ASTM D5601 60N
Cold Bending - initial 37GP56M -30
Cold Bending -90 days at 70°C 37GP56M -30
Board Thickness - 4.8 mm (3/16")
Puncture Resistance ASTM E154 500N
Water Absorption ASTM D994 0.25%
All values are nominal


Soprema Inc. may modify the composition of its products without prior notice. Consequently orders will be filled according to the latest specification.


Manufacturer: SOPREMA INC.

Contact Address: See Membership List, Section 1

Product Group: SOPRASMART ISO HD 180

Country of Origin: Canada

Country of Manufacture: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer's data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

Soprasmart ISO HD 180 is a high density composite panel composed of a non-woven polyester reinforced membrane with a thermofusible/sanded surface, laminated on an HD (100psi) polyisocyanurate insulation panel. The base sheet is offset from the board on two adjacent edges (1 inch on one end and 3-1/2 inches on 1 side) to provide shiplap; other edges are square. To ensure a secure installation, the side lap is made with a patented DUO-SELVEDGE unique to Soprema (60% self-adhesive and 40% thermofusible). Its self-adhesive component protects combustible surfaces and its thermofusible properties provide an efficient seal. End laps can be aligned then sealed by heat welding a minimum 12" wide membrane reinforcing strip centered over the end lap. Soprasmart ISO HD 180 can be mechanically fastened or adhered with Duotack adhesive.

Soprasmart Board 180 can be used for the following applications:

  • an overlay board and base sheet on all types of insulation
  • a recovery board and base sheet on existing roofing
  • an overlay board and base sheet on wood decks

PROPERTIES:

Standards Soprasmart ISO HD 180
Board Dimensions - 0.91m x 2.44m (3 x 8 ft)
Total Thickness (mm) - 15 mm (19/32")
Membrane Reinforcement - non-woven polyester
Total Weight - 4.26kg/m2 (0.87lb/sf)
Top Surface - film or sand
Underface - Polyisocyanurate HD
Membrane Thickness - 2.2mm (86.6 mils)
Breaking Strength, MD / XD 37GP56M 17.0 / 12.5 kN/m
Ultimate Elongation, MD / XD 37GP56M 60/65%
Tear Strength ASTM D5601 60N
Cold Bending - initial 37GP56M -30
Cold Bending -90 days at 70°C 37GP56M -30
Board Thickness - 12.7 mm (1/2")
Thermal Resistance (R-Value) at 24C (75F) - ASTM C518 R2.5
Compressive Strength ASTM D1621 >689kPa(100psi)
Dimensional Stability ASTM D2126 <0.5% linear change (7 day)
Water Absorption ASTM C209 <1% by volume
Resistance to Mold ASTM D3273 Passed (10)
Service Temperature - <127C (260F)
All values are nominal


Soprema Inc. may modify the composition of its products without prior notice. Consequently orders will be filled according to the latest specification.


2.7 GEORGIA PACIFIC CANADA LTD.

Manufacturer: GEORGIA PACIFIC CANADA LTD.

Contact Address: See Membership List, Section 1

Product Group: GYPSUM OVERLAY BOARD

Country of Origin: Canada

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

DensDeck is a water-resistant treated gypsum board manufactured with an embedded non structural fibreglass mat facer and a water-resistant treated core. DensDeck Prime Roof Guard is identical except that it has a treated surface to improve bonding.

DensDeck is an accepted insulation overlay board in the RoofStar Guarantee Program. DensDeck Prime Roof Guard is an accepted insulation overlay board for adhered roof assemblies in the RGC Program.

DensDeck® and DensDeck Prime™ Properties, Standards and Classifications

¼" DensDeck ¼" DensDeck Prime ½" DensDeck ½" DensDeck Prime 58" DensDeck 58" DensDeck
Prime
Thickness, inches, nominal ¼" ± 1/16" ¼" ± 1/16" ½" ± 1/32" ½" ± 1/32" 58" ± 1/32" 58" ± 1/32"
Width, standard 4' ± 18" 4' ± 18" 4' ± 18" 4' ± 18" 4' ± 18" 4' ± 18"
Length, standard 8' ± ¼" 8' ± ¼" 8' ± ¼" 8' ± ¼" 8' ± ¼" 8' ± ¼"
Weight, lb / sq. ft., nominal 1.1 1.15 1.95 1.975 2.5 2.55
Surfacing Glass mat Glass mat with non-asphaltic coating Glass mat Glass mat with non-asphaltic coating Glass mat Glass mat with non-asphaltic coating
Flexural Strength 4, parallel,
lb. min
405 405 805 805 1005 1005
Flute Spanability1 258" 258" 5" 5" 8" 8"
Permeance2 , Perms 50 50 35 35 32 32
“R” Value3 .28 .28 .56 .56 .67 .67
Linear Variation with change in temp., in / in  °F 8.5 x 10-6 8.5 x 10-6 8.5 x 10-6 8.5 x 10-6 8.5 x 10-6 8.5 x 10-6
Linear Variation with change in Moisture, in / in %RH 6.25 x 10-6 6.25 x 10-6 6.25 x 10-6 6.25 x 10-6 6.25 x 10-6 6.25 x 10-6
Water Absorption 4, % max 10.0 10.0 10.0 10.0 10.0 10.0
Compression Strength,
psi nominal
500 - 900 500 - 900 500 - 900 500 - 900 500 - 900 500 - 900
Surface water Absorption4,
Grams, nominal
2.5 <2.0 2.5 <2.0 2.5 <2.0
Flame Spread,
Smoke Developed
(ASTM E 84)
0 0 0 0 0 0
Fire Classification FMRC Class 1
(as overlayment)
UL Class A (UL 790)
ULC S-102
FMRC Class 1 (FM 4450)
UL 1256, ULC S-126
UL Class A (UL 790)
ULC S-102
FMRC Class 1 (FM 4450)
UL 1256, ULC S-126
UL Classified “P” assemblies
ULC Classified “R” assemblies
ULC S-1-1
Class A (UL 790),
ULC S-107
Mold and Mildew Resistance No growth7 No growth7 No growth7
FM Approvals6 60 and 90 psf uplift / FM Class 1-90 as an overlayment FMRC 1-60, 1-90, 1-135 FMRC 1-60, 1-90, 1-180
Bending Radius 5’ 8’ 12’

Tested in accordance with ASTM E-661 (400 lb. conc. load only for 12" and 58").

  1. Tested in accordance with ASTM E-96 (dry cup method).
  2. Tested in accordance with ASTM C 518 (heat flow meter).
  3. Tested in accordance with ASTM C 473.
  4. ASTM C 1177 minimums.
  5. Higher wind uplift ratings have been achieved by numerous membrane manufacturers using DensDeck in their FMRC-approved construction designs.
  6. Tested in accordance with ASTM D 3273.

DensDeck and DensDeck Prime Roof Guard have achieved a very comprehensive Class A (UL 790) fire rating at Underwriters Laboratories due to their outstanding fire resistance.

  • ASTM E 84 with DensDeck and DensDeck Prime Roof Guard: Flame Spread 0, Smoke Developed 0
  • ASTM E 119 with 5/8" DensDeck Fireguard Type X Roof Guard: UL Classified Type DGG

Due to the outstanding fire performance of 5/8" DensDeck Fireguard Type X Roof Guard, this product can replace any generic Type X gypsum board in an assembly in the UL Fire Resistance Directory under the prefix “P”.

  • 5/8" DensDeck Fireguard Type X Roof Guard is classified by Underwriters Laboratories and can be used in the following UL “P” assemblies: P225, P227, P230, P232, P235, P254, P257, P259, P266, P508, P510, P512, P514, P518, P701, P713, P714, P717, P718, P719, P720, P722, P724, P725, P726, P727, P728, P729, P730, P731, P732, P733, P734, P735, P736, P738, P739, P740, P801, P803, P805, P811, P813, P814, P815, P818, P819, P824, P825, P826, P828, P921
  • UL of Canada R210, R217, R222, R223, R224, R702, R703, R705, R804, R806, R808
  • ANSI / UL 1256 Steiner Tunnel “Fire Classified Construction”. This listing allows direct application on steel decking with ¼", ½" or 5/8" DensDeck or DensDeck Prime Roof Guard under foamed plastic insulations.

2.8 FIRESTONE BUILDING PRODUCTS

Manufacturer: FIRESTONE BUILDING PRODUCTS

Contact Address: See Membership List in Section 1.

Product Group: ISOGARD™ HD

Country of Origin: U.S.A.

Year First Installed: 2008

DESCRIPTION

Firestone ISOGARD™ HD Cover Board is a half-inch (12.7 mm) thick polyiso insulation designed for use as a cover board. It is a high density, closed-cell, polyisocyanurate foam core that has been manufactured with a coated glass facer. Firestone ISOGARD™ HD provides the highest thermal performance when compared to other half-inch roof cover boards.

All Firestone polyisocyanurate insulations use EPA accepted blowing agents. Firestone ISOGARD™ HD with IsoGard™ Foam Technology incorporates a HCFC-free blowing agent that does not contribute to the depletion of the ozone (ODP-free).


Note: ISOGARD HD may only be used with Firestone Roofing Systems.

PART 1 - GENERAL
The roofing material information published by the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.

1.1 COMPOSITION
1.1.1 Polyisocyanurate foam core that has been manufactured with a coated glass facer.

1.2 DELIVERY, STORAGE AND HANDLING
1.2.1 Keep insulation dry at all times.
1.2.2 Elevate insulation above the deck or ground.
1.2.3 Cover insulation with waterproof tarps.
1.2.4 Combustible. Refer to MSDS for more information.
1.2.5 Do not install over wet, damp or uneven substrates.

1.3 STANDARDS AND APPROVALS
1.3.1 Meets American Society for Testing and Materials: ASTM C1289.
1.3.2 Underwriters Laboratories Classified.
1.3.3 Factory Mutual Approved.

1.4 MANUFACTURER’S SERVICES
1.4.1 Applicator Training: Firestone offers contractor product training.
1.4.2 Technical Service: Technical Representative’s are available for consultation and field training; owners, architects and engineers are assisted in the selection and proper use of materials by technical representatives.
1.4.3 Specification / Drawings: Complete specifications and detail drawings are available upon request and on the Firestone website.

PART 2 - PRODUCTS

2.1 PHYSICAL PROPERTIES


PART 3 - EXECUTION

3.1 Insulation shall be neatly fitted to all roof penetrations, projections and nailers. No more insulation shall be installed than can be covered with membrane and completed before the end of each day’s work or before the onset of inclement weather.

Firestone ISOGARD™ HD can be applied over existing roof surfaces and under adhered or mechanically attached Single Ply, Cold and Modified Bitumen systems applied in Multi-Purpose MB Cold Adhesive and SA Base with a torch applied cap.


2.9 POSI-SLOPE WESTERN

Manufacturer: POSI-SLOPE WESTERN

Contact Address: See Membership List, Section 1

Product Group: MF - PROTECT BOARD COMPOSITE

Country of Origin: Canada

MATERIAL

Mineral fibre and asphalt board composite.

DESCRIPTION

The roofing assembly / material information published in the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s data or specifications. The preparation of a detailed specification is the responsibility of the design authority.

A rigid mineral fibre board manufactured from basalt rock and steel slag with a melting point of 2180ºF (1195ºC), excellent fire resistance properties and stable thermal values. Laminated with a top layer of fortified asphalt protection board for strength and versatility of application.

Applications: Torched, hot mopped or cold applied BUR and Modified Bituminous roofing systems. Can be fully adhered, mechanically fastened, loose-laid or in ballasted single-ply roofing systems.
Dimensions: Butt edge 60 cm (2') x 120 cm (4') and 90 cm (3') x 120 cm (4').
Slope: Unlimited; Minimum starting thickness 0" (nominal).
Compliance: CAN/CGSB 2-51.31-M84, ASTM C726 Compressive strength of mineral fibre only at 10% deformation - ASTM C165: 90 kPa (13 psi).
R Factor: R4 per inch
RSI .7 / 25 mm

SPECIFICATION

MF - Protect Board Composite consists of mineral fibre insulation, factory laminated with a 3 mm (1/8") asphalt board facer with square edges. All tapered panels shall have a uniform slope and all valley corners and crickets to be factory mitred by Posi-Slope Ent. Inc. All boards to be clearly coded and shall provide arrows to indicate the slope direction of each board. Manufacture in accordance with architect approved pre-engineered shop drawings by Posi-Slope.



2.10 ROXUL, INC.

Manufacturer: ROXUL, INC.

Contact Address: See Membership List, Section 1

Product Group: Monoboard and Monoboard Plus

Country of Origin:

DESCRIPTION

(information is currently not available)


2.11 SECUREROCK

Manufacturer:SECUREROCK

Contact Address: See Membership List in Section 1.

Product Group:

Country of Origin:

Year First Installed:

DESCRIPTION

Gypsum - Fibre Roof Board (information is currently not available) Glass - Mat Roof Board (information is currently not available)


2.12 CARLISLE SYNTEC SYSTEMS CANADA

Manufacturer: CARLISLE SYNTEC SYSTEMS CANADA

Contact Address: See Membership List in Section 1.

Product Group: COVERBOARDS - SECURSHIELD HD PLUS

Country of Origin: U.S.A.

Year First Installed: BC: 2009

DESCRIPTION

SecurShield HD Plus HD is a 12.7 mm (1/2") thick high density, closed-cell, polyisocyanurate insulation cover board. SecurShield HD Plus is ideal for use with all Carlisle mechanically attached or fully adhered EPDM or TPO roofing systems. SecurShield HD Plus is available in 1.2 m x 2.4 m (4' x 8') panels.

PART 1 - GENERAL
The roofing material information published by the RCABC Roofing Practices Manual does NOT represent a complete set of the manufacturer’s published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.

1.1 COMPOSITION
1.1.1 High density, closed-cell, polyisocyanurate. Foam core laminated to coated glass fiber mat face.

1.2 DELIVERY, STORAGE AND HANDLING
1.2.1 All materials must be stored out of the weather in a clean, dry area in the original packages with the manufacturer's labels intact.
1.2.2 Store materials elevated from the roof surface or the ground, on a pallet and covered by a waterproof tarp.
1.2.3 Materials stored on the roof must be stored in a safe manner not to exceed the allowable live load of the storage area.
1.2.4 Care must be taken when transporting and handling SecureShield HD Plus panels to avoid physical damage.
1.2.5 Do not install over wet, damp or uneven substrates.

1.3 STANDARDS AND APPROVALS
1.3.1 Meets American Society for Testing and Materials
1.3.2 Underwriters Laboratories Classified.
1.3.3 Factory Mutual Approved product.
1.3.4 UL 790

1.4 MANUFACTURER’S SERVICES
1.4.1 Applicator Training: Carlisle offers contractor product training.
1.4.2 Technical Service: Technical Representative's are available for consultation and field training; owners, architects and engineers are assisted in the selection and proper use of materials by technical representatives.
1.4.3 Specification / Drawings: Complete specifications and detail drawings are available upon request and on the Carlisle Syntec Canadawebsite.

PART 2 - PRODUCTS

2.1 PHYSICAL PROPERTIES

SecurShield HD Typical Physical Properties

Property Test Method Value
Compressive Strength ASTM D1621 (modified) 100 psi (690 kPa)
Dimensional Stability ASTM D2126 <0.5% linear change (7 days)
Water Absorption ASTM C209 <1% volume
R-value ASTM C518 2.5
Thickness 1/2"
Service Temperature 260°F or less (126°C or less)
Resistance to Mold ASTM D3273 Passed


PART 3 - EXECUTION

3.1 SecurShield HD Plus insulation must be protected from open flame and kept dry at all times. Install only as much insulation as can be covered the same day by completed roof-covering material. Carlisle will not be responsible for specific building and roof design by others, for deficiencies in construction or workmanship, for dangerous conditions on the jobsite or for improper storage and handling. Technical specifications shown in this literature are intended to be used as general guidelines only and are subject to change without notice. Call Carlisle for more specific details or refer to PIMA Technical Bulletin No. 109: Storage and Handling Recommendations for Polyiso Roof Insulation.


LEED INFO
Post-Industrial Recycled Content <9%
Manufacturing Locations Smithfield, PA
Franklin Park, IL
Tooele, UT
Terrell, TX
Lake City, FL
Kingston, NY


Back to Essential Elements

Fasteners