Difference between revisions of "Materials:(Transwest) FF 100"

Latest revision as of 15:56, 25 June 2025

Division C - Accepted Materials

FF 100
by Transwest Roofing Ltd.

The metal panel listed and described below is accepted for use in the RoofStar Guarantee Program.

Manufacturer Transwest Roofing Ltd. Contact Address See the current Membership list and contact information at www.rcabc.org Product Group - Standing Seam Metal Roof System Panel Machine New Tech Machinery Panel Name (Transwest) FF 100 Seam Type Snap Lock: 25 mm (1") The roofing assembly / material information published below and in the RCABC Roofing Practices Manual DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority. For more information about this product or system, consult the manufacturer.

OVERVIEW

The FF100 Panel is a metal roof panel formed from 24 gauge. Width from 300 mm (12") to 500 mm (20") wide with a 25 mm (1") height at the male rib. Note that the maximum length of this panel is restricted in the "RGC Standard for Architectural Sheet Metal (ASM) Roofs" to 10 m (30') because of the coefficient of expansion (Ref. Article 9.2.1.1., Sentence (8)). This panel is also suitable for application only on a solid substrate (uninsulated roofs).

Fasteners (screws) used to attach panels to plywood deck to be No. 8 by 22 mm (1") panhead. Fasteners to be placed a maximum of 600 mm (24") on center.

SYSTEM DESCRIPTION

General: Standing seam panels utilize a hidden fastener clip system for mechanical fastening to a solid substrate. The maximum spacing of the clips in either the snap lock or mechanically locked system is 600 mm OC (24"). The panels are locked together with the clips as part of the seam, by use of friction in the case of the Snap lock profiles, or by use of a mechanical seamer in the case of the mechanically locked profiles.
Range of application: on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction.
Fasteners (Screws):
1. Consult manufacturer.
Deck Requirements: in keeping with the Standard for Architectural Sheet Metal (ASM) Systems.

PROFILE

N/A

TECHNICAL DATA SHEET

N/A

SITE CONDITIONS

Contact manufacturer for installation requirements, including requirements for extreme weather areas.

PERFORMANCE REQUIREMENTS

Wind Uplift Resistance: Panel securement shall conform to the requirements in Part 3 of the Standard for Architectural Sheet Metal (ASM) Systems.
Materials:RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in Section 9.2. of the Standard.

Back to Site-Formed Metal Roofing Systems

Back to Accepted Materials

Home

@@ Line 1: / Line 1: @@
-Manufacturer: <b>TRANSWEST ROOFING LTD.</b>
+__NOTOC__
+__NONUMBEREDHEADINGS__
+{{DISPLAYTITLE:<span style="position: absolute; clip: rect(1px 1px 1px 1px); clip: rect(1px, 1px, 1px, 1px);">{{FULLPAGENAME}}</span>}}
-Contact Address: See Membership List in Section 1.
+<big><big>Division C - Accepted Materials</big></big>
+<hr>
-Product Group:<b> SEAM METAL ROOF SYSTEM - FF100 PANEL</b>
+<big><big><big><big><big>FF 100</big></big></big></big></big><br>
+<big><big><big>by Transwest Roofing Ltd.</big></big></big><br>
+{| class="wikitable"
-;<u>DESCRIPTION</u>
+|-
+| style="background-color: #ffffcc; column-width:100%" | The metal panel listed and described below is accepted for use in the '''''RoofStar Guarantee Program'''''.
-The FF100 Panel is a metal roof panel formed from 24 gauge. The panel can be applied on to solid sheeting with or without insulation. Width from 300 mm (12") to 500 mm (20") wide with a 25 mm (1") height at the male rib.  Panels are continuous with no end laps.
+|}
+{| class="wikitable"
-Fasteners (screws) used to attach panels to plywood deck to be No. 8 by 22 mm (1") panhead. Fasteners to be placed a maximum of 600 mm (24") on center.
+|-
+|
-;<u>PART 1 - GENERAL</u>
+;'''Manufacturer''': Transwest Roofing Ltd.
+;'''Contact Address''': See the current Membership list and contact information at [http://www.rcabc.org/members/find-a-member/ www.rcabc.org]
-:1.1 The roofing assembly / material information published in the <b>RCABC <i>Roofing Practices Manual</i></b> DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.
+;'''Product Group - Standing Seam Metal Roof System'''
+;'''Panel Machine''': New Tech Machinery
-;1.2 <u>SYSTEM DESCRIPTION</u>
+;'''Panel Name''': (Transwest) FF 100
-:.1 Metal panels employ a hidden fastening system for securement to a solid substrate. 1" Snap-Lock panels are produced with a nail strip to eliminate the use of clips and allows the panel seams to interlock without having to use a mechanical seaming device.
+;'''Seam Type''': Snap Lock: 25 mm (1")
-:.2 Range of application: on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; also used for roof replacement (retrofit) application.
-;1.3 <u>DELIVERY, STORAGE AND HANDLING</u>
+The roofing assembly / material information published below and in the [http://{{SERVERNAME}}/index.php?title=Main_Page RCABC Roofing Practices Manual] DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.  For more information about this product or system, consult the manufacturer.
-:.1 Protect against damage and discoloration.
+|}
-:.2 Handle panels with non-marring slings.
-:.3 Do not bend panels.
-:.4 Store panels above ground, with one end elevated for drainage.
-:.5 Protect panels against standing water and condensation between adjacent surfaces.
-:.6 If panels become wet, immediately separate sheets, wipe dry with clean cloth, allow to air dry.
-;<u>PART 2 - PRODUCTS</u>
+====OVERVIEW====
+The FF100 Panel is a metal roof panel formed from 24 gauge. Width from 300 mm (12") to 500 mm (20") wide with a 25 mm (1") height at the male rib.  Note that the maximum length of this panel is restricted in the "RGC Standard for Architectural Sheet Metal (ASM) Roofs" to 10 m (30') because of the coefficient of expansion (Ref. [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#9.2.1.1._Panel_Grade.2C_Gauge.2C_and_Fabrication Article 9.2.1.1., Sentence (8))].  This panel is also suitable for application only on a solid substrate (uninsulated roofs).
-;2.1 <u>FABRICATION</u>
+Fasteners (screws) used to attach panels to plywood deck to be No. 8 by 22 mm (1") panhead. Fasteners to be placed a maximum of 600 mm (24") on center.
-:.1  Unless otherwise shown on drawings or specified herein, fabricate panels in continuous one piece lengths and fabricate flashings and accessories in longest practical lengths.
-:.2  Roofing panels shall be factory formed. Field formed panels are not acceptable.
-;2.2 <u>PERFORMANCE REQUIREMENTS</u>
+====SYSTEM DESCRIPTION====
+#'''General''':  Standing seam panels utilize a hidden fastener clip system for mechanical fastening to a solid substrate. The maximum spacing of the clips in either the snap lock or mechanically locked system is 600 mm OC (24"). The panels are locked together with the clips as part of the seam, by use of friction in the case of the Snap lock profiles, or by use of a mechanical seamer in the case of the mechanically locked profiles.
+#'''Range of application''': on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction.
+#'''Fasteners (Screws)''':
+##Consult manufacturer.
+#'''Deck Requirements''': in keeping with the [http://rpm.rcabc.org/index.php?title=Standard_for_Architectural_Sheet_Metal_(ASM)_Systems Standard for Architectural Sheet Metal (ASM) Systems].
-:.1 <u>Wind Uplift Standards</u>:
+====PROFILE====
+N/A
+====TECHNICAL DATA SHEET====
+N/A
-::National Research Council (NRC-CNRC) Report No.B1040 Wind Uplift Resistance of Metal Roofing. The NRC-CNRC Report No. B1040 test results confirm that an acceptable level of wind uplift resistance can be achieved with RGC Accepted Metal Panel Systems on typical roof designs over solid decking for most British Columbia geographical locations. Refer to Appendix II for calculations for typical roof wind uplift pressure requirements for buildings located in the Province of British Columbia.
+====SITE CONDITIONS====
+#Contact manufacturer for installation requirements, including requirements for extreme weather areas.
-::A simplified design procedure developed by NRC-CNRC for selecting wind pressure calculations for metal roof assemblies by region (location) and building height in the Province of British Columbia is provided in Section 8.1.5 to assist designers.
+====PERFORMANCE REQUIREMENTS====
+<ol>
-::RGC accepted metal panel systems shall be formed of steel conforming to one of the following material specifications, as applicable:
+<li>'''Wind Uplift Resistance''': Panel securement shall conform to the requirements in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#PART_3 Part 3] of the [http://rpm.rcabc.org/index.php?title=Standard_for_Architectural_Sheet_Metal_(ASM)_Systems Standard for Architectural Sheet Metal (ASM) Systems].
+<li>'''Materials''':RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#Section_9.2._Materials Section 9.2.] of the Standard.
-::* ASTM Standard Specification A653 / A653M, Sheet Steel, Zinc-Coated (Galvanized) or Zinc-Iron Alloy Coated (Galvannealed) by the hot dip process, minimum Grade 33, with a design thickness of 24 gauge. (0.024") or greater and a minimum zinc coating designation Z275 (G-90).
+</li></ol>
-::* ASTM Standard Specification A792 / A792M, Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process, minimum Grade 33, with a design thickness of 24 gauge (0.024") or greater and minimum coating designation AZ150.
-;<u>PART 3 - EXECUTION</u>
-;3.1 <u>EXAMINATION - EXISTING CONDITIONS</u>
-:.1  Verify that structural deck to receive panels is complete, in true plane, secure and otherwise properly prepared.
-:.2  Prior to starting work, notify General Contractor about defects requiring correction.
-:.3  Do not start work until conditions are satisfactory.
-;3.2 <u>PREPARATION - FIELD MEASUREMENTS</u>
-:.1  Verify prior to fabrication.
-:.2  If field measurements differ from drawing dimensions, notify Architect / Professional Engineer prior to fabrication.
-;3.3 <u>PROTECTION</u>
-:.1 Treat, or isolate with protective material, any contacting surfaces of dissimilar materials to prevent electrolytic corrosion.
 <hr>
+[[Architectural Metal Roofing|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''Site-Formed Metal Roofing Systems'']]
+[[Materials by Product Type|<i class="fa fa-chevron-circle-left fa" ></i> Back to ''Accepted Materials'']]
-[[Architectural Metal Roofing|<i class="fa fa-chevron-circle-left fa-2x" ></i> Back to ''Site-Formed Metal Roofing Systems'']]
 [[Main Page|Home]]