Difference between revisions of "Materials:(Cascade) Nu-Tech Snap-Loc"

Revision as of 15:33, 1 October 2018

The metal panel listed and described below is accepted for use in the RoofStar Guarantee Program.

Manufacturer Cascade Roofing & Exteriors Inc. Contact Address See the current Membership list and contact information at www.rcabc.org Product Group - Standing Seam Metal Roof System Panel Machine New Tech Panel Name Snap-Loc Seam Type Snap Lock The roofing assembly / material information published below and in the RCABC Roofing Practices Manual DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority. For more information about this product or system, consult the manufacturer.

OVERVIEW

The Nu-Tech Snap-Loc is an on-site continuous panel metal roofing machine. Panel profiles vary from 300 mm (12") to 457 mm (18") wide with a 44 mm (1¾") rib.

On-site roll forming provides for the elimination of end laps with continuous panel forming capabilities in lengths up to nominal 46 m (150').

SYSTEM DESCRIPTION

General: The Snap-Loc Nu-Tech 44 mm (1¾") is a snap lock concealed fastener roofing panel. The panel can be formed in any width between 300 mm (12") to 457 mm (18"). Stiffening ribs, striations and / or clip relief can be added depending on the application. The male leg locks along the entire length of the panel and does not rely upon clips to provide additional locking. The Snap-Loc Nu-Tech utilizes 153 mm (6¹/₈") of metal in forming the panel legs providing greater structural integrity, which can carry greater loads.
Range of application: On wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction.
Fasteners (Screws): Fasteners used to attach panel clips to steel to be No. 10 - 16 by 25 mm (1") long cadmium plated pancake head, No. 2 Phillips drive, No. 3 self-drilling point steel screws. Two screws per clip inserted through 6.25 mm (¼") diameter guide holes.
Roof Deck Fasteners (Panel Clips): One-piece assembly, No. 22 MSG min. thick, 88 mm (3½") high. One panel clip spaced at 600 mm (24") O.C. for Class 90.

PROFILE

N/A

TECHNICAL DATA SHEET

N/A

SITE CONDITIONS

Minimum roof slope is 1:4 (3" in 12"). Severe conditions (heavy snow or ice) minimum slope is 1:1.5 (8" in 12").

PERFORMANCE REQUIREMENTS

Wind Uplift Standards: Engineered designs to resist wind uplift may refer to the British Columbia Building Code, Div. B, Appendix C, Table C-2 which lists various types of loads, including wind loads, for specific reference locations throughout the province. See also Guides and Notes (Wind Resistance) for a simplified calculation procedure. Regardless of the resources indicated here, the Design Authority is responsible to perform accurate wind load calculations and specify securement requirements.
Materials:RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the standards published in the RoofStar Guarantee Standards for ASM Roof Assemblies.

Back to Site-Formed Metal Roofing Systems

Back to Accepted Materials

Home

@@ Line 10: / Line 10: @@
 ;'''Manufacturer''': Cascade Roofing & Exteriors Inc.
 ;'''Contact Address''': See the current Membership list and contact information at [http://www.rcabc.org/members/find-a-member/ www.rcabc.org]
-;'''Product Group - Standing Seam Metal Roof System''': Nu-Tech Snap-Loc
+;'''Product Group - Standing Seam Metal Roof System'''
+;'''Panel Machine''': New Tech
+;'''Panel Name''': Snap-Loc
+;'''Seam Type''': Snap Lock
 The roofing assembly / material information published below and in the [http://{{SERVERNAME}}/index.php?title=Main_Page RCABC Roofing Practices Manual] DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.  For more information about this product or system, consult the manufacturer.
@@ Line 23: / Line 26: @@
 #'''General''': The Snap-Loc Nu-Tech 44 mm (1&#190;") is a snap lock concealed fastener roofing panel. The panel can be formed in any width between 300 mm (12") to 457 mm (18"). Stiffening ribs, striations and / or clip relief can be added depending on the application. The male leg locks along the entire length of the panel and does not rely upon clips to provide additional locking. The Snap-Loc Nu-Tech utilizes 153 mm (6<sup>1</sup>/<sub>8</sub>") of metal in forming the panel legs providing greater structural integrity, which can carry greater loads.
 #'''Range of application''': On wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction.
-#'''Panel Attachment''':
+#'''Fasteners (Screws)''': Fasteners used to attach panel clips to steel to be No. 10 - 16 by 25 mm (1") long cadmium plated pancake head, No. 2 Phillips drive, No. 3 self-drilling point steel screws. Two screws per clip inserted through 6.25 mm (&#188;") diameter guide holes.
-::* '''Fasteners (Screws)''': Fasteners used to attach panel clips to steel to be No. 10 - 16 by 25 mm (1") long cadmium plated pancake head, No. 2 Phillips drive, No. 3 self-drilling point steel screws. Two screws per clip inserted through 6.25 mm (&#188;") diameter guide holes.
+#'''Roof Deck Fasteners (Panel Clips)''': One-piece assembly, No. 22 MSG min. thick, 88 mm (3&#189;") high. One panel clip spaced at 600 mm (24") O.C. for Class 90.
-::* '''Roof Deck Fasteners (Panel Clips)''': One piece assembly, No. 22 MSG min. thick, 88 mm (3&#189;") high. One panel clip spaced at 600 mm (24") on centre for Class 90.
 ====PROFILE====