Drafting - Division A, C

This page is used for drafting new or revised wordings, before publishing

USING TESTED ASSEMBLY REPORTS The tables and products shown below provide basic material data related to roof assemblies tested for their performance in modulating and high winds, using the test method found in CSA A123.21. They also provide links to more information about the materials, including manufacturers' published Technical Data sheets. The reader is advised to use this information in conjunction with other RoofStar-accepted Materials, and with reference to roof system requirements derived from from appropriate wind uplift calculations (see the Wind-RCI calculator and reference notes and requirements outlined in Securing the Roof Assembly; also refer to the BC Building Code, Part 4 and Part 5). The information on this page is not intended for use as a comparison of material performance or quality. Nor should this information be construed as an endorsement of the suitability of any given material for a particular application. It is the sole responsibility of the Design Authority to assess the performance capability and material suitability for specific design requirements. Roof Assemblies are classified according to three different approaches to securement: MARS (Mechanically Attached Roof Systems), PARS (Partially Adhered Roof Systems), and AARS (Adhesive Applied Roof Systems). For a full explanation of these and other key details pertinent to an understanding of the test reports, visit Securing the Roof Assembly. In the tables below, the following definitions apply: ASSEMBLIES are represented by the downloadable reports linked in the far right column of each table. Assemblies are defined in this Manual as the arrangement of various and distinct roofing materials in combination with the supporting deck structure. Therefore, a Tested Assembly refers to both the roof system materials and the type of supporting deck structure to which they are secured and then tested in a controlled environment, in accordance with the CSA A123.21 test method. Some reports provide guidance for other deck types. The reader is advised to consult each report for optional assemblies and the testing authority's remarks concerning resistance to Specified Wind Loads (refer to the BC Building Code, Part 4). SYSTEMS used in the tables below refers to the system of securement - that is, the pattern or spacing of fasteners or adhesive ribbons used to achieve the listed Dynamic Uplift Resistance (DUR) values (NOTE: the term System used elsewhere in the RPM denotes the combination of roof materials, excluding the supporting deck structure. The two uses of system should not be confused). Some Assemblies have been tested with a variety of securement systems, others with only one. For example, one Assembly may be tested with three different fastener spacing arrangements (securement systems), indicated both by the row spacing and by the fastener spacing. In that case, the tables show that a material has been tested with three different systems of securement. You will see notations in the third column of each table indicating how many securement systems have been tested for a particular material. The associated downloadable report will be found on the same line, in the far right column. The report name is a hyperlink to the report document. Some of the reports will include diagrams or photographs illustrating the tested patterns. Click on a report link for a complete description of the test results and all other materials tested in the assembly (NOTE: Most reports are under 2 MB in size but some are considerably larger and may exceed your server capacity) How to Use the Tables Begin by determining the Specified Wind Loads of the roof using the online calculator available through Wind-RCI (click here for a sample report). For roofs that do not conform to the parameters of the Wind-RCI online calculator, the Specified Wind Loads will have to be calculated by a qualified professional. Refer to the BC Building Code, Part 4 for guidance and specific formulae; familiarize yourself with the three roof zones and their respective Specified Wind Loads. The Corner Zone represents the highest anticipated Specified Wind Loads for the roof; consequently, you should use the Corner Zone value for selecting an appropriate Tested Assembly. The Specified Wind Loads for the Edge and Field zones may be considered later; The current page you are on displays materials and tested assembly reports for one method, or system, by which the roof will be fastened together. To switch to another type of system, click on one of the links below: MARS Systems (mechanically fastened); AARS Systems (adhered); PARS Systems (a combination of adhered and mechanically fastened). Note that the method of attachment may be determined by the type of supporting deck structure. Expand the table for the membrane type and look for maximum wind uplift resistance values that exceed the requirements determined through the RCI calculator or professional calculations using the formulae in the BCBC, Part 4; (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required Safety Factor of 1.5 - these are called the DUR or Dynamic Uplift Resistance values) Open the report for the Tested Assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer); In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, locate a possible alternate in the Accepted Materials section of this Manual. If you are unsure about compatibility, contact the manufacturer of the Tested Assembly, or contact the RCABC.

1 SBS Membrane Systems

How to use Tested Assembly ReportsSBS Base MembranesSBS Cap MembranesSBS Single-ply Membranes

1. The tables on the adjacent tabs display data and links to Tested Assembly Reports listed by the membrane type shown on the tab. These are reports that detail the makeup and performance of roof systems tested using the CSA-A123.21 Standard test method for the dynamic wind uplift resistance of membrane-roofing systems (latest edition). Use the maximum wind uplift values that equal or exceed the highest Specified Wind Loads; these are calculated using either the online Wind-RCI calculator or through manual engineering calculations (see the British Columbia Building Code, Division B, Part 4 (4.1.7 Specified Wind Loads));
   (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required safety factor of 1.5)
2. Open the report for the tested assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer);
3. In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, consult the manufacturer of the Tested Assembly for alternates that are accepted by the RoofStar Guarantee Program, and obtain the manufacturer's written approval.

Primary Material			Secondary Materials & Deck					Tested Assembly Report Data
Manufacturer	Membrane		Insulation Overlay	Insulation	Deck Overlay	Deck		Tested Systems	kPa		Psf		Downloadable Test Report	Test Facility	Test Facility Report No.
									Low	High	Low	High
IKO Industries Ltd.	Fast-N-Stick-180 Base		----	----	----	Steel		2	-1.90	-4.8	-40.00	-100.00	MARS Test Report 1	exp. Service Inc.	PUB-DRU292551
IKO Industries Ltd.	Fast-N-Stick HD Base		----	----	----	Steel		3	-2.40	-5.10	-50.00	-106.00	MARS Test Report 2	exp. Service Inc.	PUB-DRU285771
Soprema Inc.	Soprafix Base 630		----	----	----	Steel Steel Steel Steel		4 1 3 4	-2.00 --- -1.60 -2.00	-6.20 -2.40 -3.20 -6.20	-42.00 --- -33.00 -42.00	-130.00 -50.00 -67.00 -130.00	MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 10	exp. Service Inc.	PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRU339156

Primary Material			Primary Material					Tested Assembly Report Data
Manufacturer	Membrane		Insulation Overlay	Insulation	Deck Overlay	Deck		Tested Systems	kPa		Psf		Downloadable Test Report	Test Facility	Test Facility Report No.
									Low	High	Low	High
IKO Industries Ltd.	Armourcool Granular TP-HD Cap		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Torchflex TP-180 Cap		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Torchflex TP-250 Cap 5mm		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Torchflex TP-250 Cap		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Torchflex TP-HD-Cap		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Prevent TP 250 Cap 4 mm		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Prevent TP-HD-Cap		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
IKO Industries Ltd.	Prevent Premium TP 250 Cap 4 mm		----	----	----	Steel Steel		2 3	-1.90 -2.40	-4.80 -5.10	-40.00 -50.00	-100.00 -106.00	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU292551 PUB-DRU285771
Soprema Inc.	Soprafix Traffic Cap 660		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Soprafix Traffic Cap FR 661		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Soprafix Unilay 750		----	----	----	Steel		4	-2	-5.2	-41	-108	MARS Test Report 7	exp. Service Inc.	PUB-DRU168549
Soprema Inc.	Sopralene Flam 180 GR		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Sopralene Flam 250 GR		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Sopralene Mammouth GR		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Sopraply Traffic Cap 560		----	----	----	Steel Steel Steel Steel Steel		3 3 3 3 2	-1.8 -2.4 -2.4 -1.9 -1.8	-3.4 -5.2 -5.2 -4.8 -2.4	-37 -50 -50 -40 -37	-70 -108 -108 -100 -50	MARS Test Report 1 MARS Test Report 2 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	Sopraply Traffic Cap FR 561		----	----	----	Steel Steel Steel Steel Steel		3 3 3 3 2	-1.8 -2.4 -2.4 -1.9 -1.8	-3.4 -5.2 -5.2 -4.8 -2.4	-37 -50 -50 -40 -37	-70 -108 -108 -100 -50	MARS Test Report 1 MARS Test Report 2 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321
Soprema Inc.	SopraStar Flam HD GR		----	----	----	Steel Steel Steel Plywood Plywood Steel Steel Steel		3 3 4 1 3 3 3 2	-1.80 -2.40 -2.00 ---- -1.60 -2.40 -1.90 -1.80	-3.40 -5.20 -6.20 -2.40 -3.20 -5.20 -4.80 -2.40	-37.00 -50.00 -42.00 ---- -33.00 -50.00 -40.00 -37.0	-70.00 -108.00 -130.00 -50.00 -67.00 -108.00 -100.00 -50.00	MARS Test Report 1 MARS Test Report 2 MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6 MARS Test Report 8 MARS Test Report 9	exp. Service Inc.	PUB-DRU168525 PUB-DRU168520 PUB-DRU168540 PUB-DRU168534 PUB-DRU206751 PUB-DRC304890 PUB-DRU168553 PUB-DRU209321

Manufacturer	Product Name	Number of Tested Systems (per report)	kPa (Low)	kPa (High)	Psf (Low)	Psf (High)	Deck Type	Downloadable Test Report	Test Facility	Test Facility Report No.
Soprema Inc.	Soprafix Unilay 750	4 Tested Systems 4 Tested Systems	-2.00 -2.00	-5.20 -5.20	-41.00 -41.00	-108.00 -108.00	Steel Steel	MARS Test Report 7 MARS Test Report 14	exp. Service Inc.	PUB-DRU168549 SOPI-216809-T10 / SOPI-019-059-000

2 EPDM Membrane Systems

How to use Tested Assembly ReportsEPDM/Elastomeric Membranes

1. The tables on the adjacent tabs display data and links to Tested Assembly Reports listed by the membrane type shown on the tab. These are reports that detail the makeup and performance of roof systems tested using the CSA-A123.21 Standard test method for the dynamic wind uplift resistance of membrane-roofing systems (latest edition). Use the maximum wind uplift values that equal or exceed the highest Specified Wind Loads; these are calculated using either the online Wind-RCI calculator or through manual engineering calculations (see the British Columbia Building Code, Division B, Part 4 (4.1.7 Specified Wind Loads));
   (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required safety factor of 1.5)
2. Open the report for the tested assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer);
3. In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, consult the manufacturer of the Tested Assembly for alternates that are accepted by the RoofStar Guarantee Program, and obtain the manufacturer's written approval.

Manufacturer	Product Name	Number of Tested Systems (per report)	kPa (Low)	kPa (High)	Psf (Low)	Psf (High)	Deck Type	Downloadable Test Report	Test Facility	Test Facility Report No.
Firestone Building Products	Rubbergard EPDM Membrane	1 Tested System 1 Tested System	---- ----	-2.90 -3.70	---- ----	-60.00 -67.00	Steel	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU283221 PUB-DRU303359
Firestone Building Products	Rubbergard ECO White EPDM Membrane	1 Tested System 1 Tested System	---- ----	-2.90 -3.70	---- ----	-60.00 -67.00	Steel	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-DRU283221 PUB-DRU303359

3 TPO Membranes

How to use Tested Assembly ReportsTPO Membranes

1. The tables on the adjacent tabs display data and links to Tested Assembly Reports listed by the membrane type shown on the tab. These are reports that detail the makeup and performance of roof systems tested using the CSA-A123.21 Standard test method for the dynamic wind uplift resistance of membrane-roofing systems (latest edition). Use the maximum wind uplift values that equal or exceed the highest Specified Wind Loads; these are calculated using either the online Wind-RCI calculator or through manual engineering calculations (see the British Columbia Building Code, Division B, Part 4 (4.1.7 Specified Wind Loads));
   (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required safety factor of 1.5)
2. Open the report for the tested assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer);
3. In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, consult the manufacturer of the Tested Assembly for alternates that are accepted by the RoofStar Guarantee Program, and obtain the manufacturer's written approval.

Manufacturer	Product Name	Number of Tested Systems (per report)	kPa (Low)	kPa (High)	Psf (Low)	Psf (High)	Deck Type	Downloadable Test Report	Test Facility	Test Facility Report No.
Carlisle Syntec Systems Canada	Sure-Weld 45 mil TPO Membrane	1 Tested System 1 Tested System	---- ----	-3.40 -3.40	---- ----	-70.00 -71.00	Steel Steel	MARS Test Report 3 MARS Test Report 4	exp. Service Inc.	PUB-DRU236018 PUB-DRU168402
Firestone Building Products	Ultraply 1.2 mm TPO Membrane	1 Tested System 2 Tested Systems 1 Tested System 1 Tested System	---- -3.80 ---- ----	-3.20 -4.20 -3.80 -3.00	---- -80.00 ---- ----	-67.00 -87.00 -80.00 -63.00	Steel Steel Steel Steel	MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6	exp. Service Inc.	PUB-DRU303384 PUB-DRU168455 PUB-DRU303385 PUB-DRU168431
Firestone Building Products	UltraPly 1.6 mm TPO Membrane	1 Tested System 2 Tested Systems 1 Tested System 1 Tested System	---- -3.80 ---- ----	-3.20 -4.20 -3.80 -3.00	---- -80.00 ---- ----	-67.00 -87.00 -80.00 -63.00	Steel Steel Steel Steel	MARS Test Report 3 MARS Test Report 4 MARS Test Report 5 MARS Test Report 6	exp. Service Inc.	PUB-DRU303384 PUB-DRU168455 PUB-DRU303385 PUB-DRU168431
Johns Manville Corporation	JM TPO-45	1 Tested System	----	-3.6 -5.0	----	-75.0 -105.0	Steel Steel	MARS Test Report 3 MARS Test Report 4	exp. Service Inc.	PUB-DRU292367 PUB-DRU292360
Johns Manville Corporation	JM TPO-60	1 Tested System	----	-3.6 -5.0	----	-75.0 -105.0	Steel Steel	MARS Test Report 3 MARS Test Report 4	exp. Service Inc.	PUB-DRU292367 PUB-DRU292360
Johns Manville Corporation	JM TPO-80	1 Tested System	----	-3.6 -5.0	----	-75.0 -105.0	Steel Steel	MARS Test Report 3 MARS Test Report 4	exp. Service Inc.	PUB-DRU292367 PUB-DRU292360

4 PVC Membranes

How to use Tested Assembly ReportsPVC Membranes

1. The tables on the adjacent tabs display data and links to Tested Assembly Reports listed by the membrane type shown on the tab. These are reports that detail the makeup and performance of roof systems tested using the CSA-A123.21 Standard test method for the dynamic wind uplift resistance of membrane-roofing systems (latest edition). Use the maximum wind uplift values that equal or exceed the highest Specified Wind Loads; these are calculated using either the online Wind-RCI calculator or through manual engineering calculations (see the British Columbia Building Code, Division B, Part 4 (4.1.7 Specified Wind Loads));
   (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required safety factor of 1.5)
2. Open the report for the tested assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer);
3. In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, consult the manufacturer of the Tested Assembly for alternates that are accepted by the RoofStar Guarantee Program, and obtain the manufacturer's written approval.

Manufacturer	Product Name	Number of Tested Systems (per report)	kPa (Low)	kPa (High)	Psf (Low)	Psf (High)	Deck Type	Downloadable Test Report	Test Facility	Test Facility Report No.
Carlisle Syntec Systems Canada	Sure-Flex 50 mil PVC Membrane	1 Tested System 1 Tested System	---- ----	-3.40 -2.30	---- ----	-70.00 -47.00	Steel Steel	MARS Test Report 1 MARS Test Report 2	exp. Service Inc.	PUB-CRU237226 RAP-DRU208111
Johns Manville Corporation	JM PVC (60 mil.)	1 Tested System	----	-3.60	----	-75.0	Steel	MARS Test Report 1	exp. Service Inc.	PUB-DRU292249
Johns Manville Corporation	JM PVC (80 mil.)	1 Tested System	----	-3.60	----	-75.0	Steel	MARS Test Report 2	exp. Service Inc.	PUB-DRU292249

5 Insulation Overlays

How to use Tested Assembly ReportsComposite Overlays

1. The tables on the adjacent tabs display data and links to Tested Assembly Reports listed by the membrane type shown on the tab. These are reports that detail the makeup and performance of roof systems tested using the CSA-A123.21 Standard test method for the dynamic wind uplift resistance of membrane-roofing systems (latest edition). Use the maximum wind uplift values that equal or exceed the highest Specified Wind Loads; these are calculated using either the online Wind-RCI calculator or through manual engineering calculations (see the British Columbia Building Code, Division B, Part 4 (4.1.7 Specified Wind Loads));
   (NOTE: while the reports show two different values for tested maximum assembly strength, the RPM tables display only the values adjusted for the required safety factor of 1.5)
2. Open the report for the tested assembly that fits with the design parameters you have chosen and calculated, and examine the report. It will break down the assembly by its components. Ensure all the key components (Secondary materials, such as deck overlay, insulation and insulation overlay) are accepted by the RoofStar Guarantee Program (note that fasteners and adhesives currently are not listed in this Manual - use the materials specified in the wind test report, or consult the membrane manufacturer);
3. In cases where a tested Secondary material is not accepted by the RoofStar Guarantee Program, look for alternates which often are published in the each report. In the absence of published alternates, consult the manufacturer of the Tested Assembly for alternates that are accepted by the RoofStar Guarantee Program, and obtain the manufacturer's written approval.

Manufacturer	Product Name	Number of Tested Systems (per report)	kPa (Low)	kPa (High)	Psf (Low)	Psf (High)	Deck Type	Downloadable Test Report	Test Facility	Test Facility Report No.
Soprema Inc.	Soprasmart ISO HD 180	3 Tested Systems	-2.40	-5.20	-50.00	-108.00	Steel	MARS Test Report 6	exp. Service Inc.	PUB-DRC304890
Soprema Inc.	Soprasmart Board 180	3 Tested Systems	-2.40	-5.20	-50.00	-108.00	Steel	MARS Test Report 6	exp. Service Inc.	PUB-DRC304890
Soprema Inc.	Xpress Board HD	3 Tested Systems 3 Tested Systems	-1.90 -1.90	-4.80 -4.80	-40.00 -40.00	-100.00 -100.00	Steel	MARS Test Report 8 MARS Test Report 11	exp. Service Inc.	PUB-DRU168553 PUB-DRU339785
Soprema Inc.	Xpress ISO	2 Tested Systems 2 Tested Systems	-1.80 -1.80	-2.40 -2.40	-37.00 -37.00	-50.00 -50.00	Steel	MARS Test Report 9 MARS Test Report 13	exp. Service Inc.	PUB-DRU209321 SOPI-020-059-010
Soprema Inc.	Soprabase HD	3 Tested Systems	-2.40	-5.20	-50.00	-108.00	Steel	MARS Test Report 12	exp. Service Inc.	SOPI-019-059-400

---

Accepted Materials

Home