Accepted Materials - ASM Roof Systems
Jump to: navigation,
search
Accepted Materials - ASM Roof Systems
Revision as of 19:50, 23 October 2017 by James Klassen (talk | contribs) (→Proprietary Metal Roof Systems (Manufactured in Plant Roll-forming))
| To view materials in any section listed below, click on the Expand button located at the right hand side of this page |
1 Vapour Retarders
The RCABC does not specify Vapour Retarders, as they are not included in the RoofStar Guarantee Program. See manufacturer specifications where Vapour Retarders are required, and refer to proprietary products and installation instructions. This cross-reference is listed for information only.
Expand
2 Deck Overlay Boards
| Manufacturer | Product Name | Product Type | Thickness mm (in.) |
Weight (lb/square foot) |
Comp. Strength (psi, nominal) |
Acceptable Application |
|---|---|---|---|---|---|---|
| Plywood | Plywood overlay | 12.7 (1/2) min. | Variable | - | All decks* | |
| Georgia-Pacific Canada Ltd. | DensDeck Roofboard | Moisture-resistant gypsum core board | 6.4 (1/4) | 1.100 | 500-900 | All decks |
| Georgia-Pacific Canada Ltd. | DensDeck Roofboard | Moisture-resistant gypsum core board | 12.7 (1/2) | 1.950 | 500-900 | All decks |
| Georgia-Pacific Canada Ltd. | DensDeck Roofboard | Moisture-resistant gypsum core board | 15.9 (5/8) | 2.500 | 500-900 | All decks |
| Georgia-Pacific Canada Ltd. | DensDeck® Prime with EONIC Roof Board | Moisture-resistant gypsum core board | 6.4 (1/4) | 1.150 | 900 | All decks |
| Georgia-Pacific Canada Ltd. | DensDeck® Prime with EONIC Roof Board | Moisture-resistant gypsum core board | 12.7 (1/2) | 1.975 | 900 | All decks |
| Georgia-Pacific Canada Ltd. | DensDeck® Prime with EONIC Roof Board | Moisture-resistant gypsum core board | 15.9 (5/8) | 2.550 | 900 | All decks |
| USG (CGC) SecureRock | Securerock Glass-Mat Roof Board | Moisture-resistant gypsum core board | 6.4 (1/4) | 1.200 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Glass-Mat Roof Board | Moisture-resistant gypsum core board | 12.7 (1/2) | 2.000 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Glass-Mat Roof Board | Moisture-resistant gypsum core board | 15.9 (5/8) | 2.700 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Gypsum Fibre Roof Board | Moisture-resistant gypsum core board | 6.4 (1/4) | 1.570 | 1800 | All decks |
| USG (CGC) SecureRock | Securerock Gypsum Fibre Roof Board | Moisture-resistant gypsum core board | 9.5 (3/8) | 1.960 | 1800 | All decks |
| USG (CGC) SecureRock | Securerock Gypsum Fibre Roof Board | Moisture-resistant gypsum core board | 12.7 (1/2) | 2.760 | 1800 | All decks |
| USG (CGC) SecureRock | Securerock Gypsum Fibre Roof Board | Moisture-resistant gypsum core board | 15.9 (5/8) | 3.200 | 1800 | All decks |
| USG (CGC) SecureRock | Securerock Coated Ultralight Glass Mat Roof Board* | 6.4 (1/4) | 1.200 | 700-1000 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Coated Ultralight Glass Mat Roof Board* | 12.7 (1/2) | 1.700 | 700-1000 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Coated Ultralight Glass Mat Roof Board* | 15.9 (5/8) | 2.200 | 700-1000 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Ultralight Glass Mat Roof Board | Moisture-resistant gypsum core board | 6.4 (1/4) | 1.200 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Ultralight Glass Mat Roof Board | Moisture-resistant gypsum core board | 12.7 (1/2) | 1.700 | 700-1000 | All decks |
| USG (CGC) SecureRock | Securerock Ultralight Glass Mat Roof Board | Moisture-resistant gypsum core board | 15.9 (5/8) | 2.200 | 700-1000 | All decks |
- * Indicates conditions of acceptance. See the product page for more information.
3 Insulation
Expand
- Composite Board Insulation
| Manufacturer | Product Name | System Test Type (Wind) | Density (kg/cu. m) | Compressive Strength (kPa/25.4 mm) | Compressive Strength (psi/1 in. thick) | Thermal Resistance (RSI/25.4 mm) | Thermal Resistance (R/inch) |
|---|---|---|---|---|---|---|---|
| Posi-Slope Western | MF (Protect Board Composite) | ‒ | ‒ | ‒ | ‒ | ‒ | ‒ |
| Soprema Inc. | Xpress Board HD | ‒ | 200 | 190 (at 25%) | 28 (at 25%) | 0.70 K/W | 4 |
| Soprema Inc. | Xpress ISO | ‒ | ‒ | 138 (Polyiso only) | 20 (Polyiso only) | 1.0 | 5.7 |
Expand
- XPS (Extruded Expanded Polystyrene Foam)
| Manufacturer | Product Name | System Test Type (Wind) | Density (kg/cu. m) | Compressive Strength (kPa) |
Compressive Strength (psi) |
Thermal Resistance (RSI/25.4 mm) |
Thermal Resistance (R/inch) |
|---|---|---|---|---|---|---|---|
| Dupont Specialty Products Division - Safety and Construction | Deckmate (Type 2) | ‒ | ‒ | 110 | 16 | 0.87 | 5 |
| Dupont Specialty Products Division - Safety and Construction | Deckmate Plus (Type 3) | ‒ | ‒ | 140 | 20 | 0.87 | 5 |
| Dupont Specialty Products Division - Safety and Construction | Roofmate (Type 4) | ‒ | ‒ | 240 | 35 | 0.87 | 5 |
| Dupont Specialty Products Division - Safety and Construction | Roofmate CT (Type 4) | ‒ | ‒ | 240* | 35* | 0.87 | 5 |
| Owens Corning Canada | Foamular C200 (Type 3) | ‒ | ‒ | 140 | 20 | 0.88 | 5 |
| Owens Corning Canada | Foamular F350 (Type 4) | ‒ | ‒ | 240 | 35 | 0.88 | 5 |
| Owens Corning Canada | Foamular 400 (Type 4) | ‒ | ‒ | 275 | 40 | 0.88 | 5 |
| Owens Corning Canada | Foamular 600 (Type 4) | ‒ | ‒ | 415 | 60 | 0.88 | 5 |
| Owens Corning Canada | Foamular 1000 (Type 4) | ‒ | ‒ | 690 | 100 | 0.88 | 5 |
| Owens Corning Canada | Foamular 404 (Type 4) | ‒ | ‒ | 276 | 40 | 0.88 | 5 |
| Owens Corning Canada | Foamular 604 (Type 4) | ‒ | ‒ | 414 | 60 | 0.88 | 5 |
| Owens Corning Canada | Foamular 404RB (Type 4) | ‒ | ‒ | 276 | 40 | 0.84 | 4.75 |
| Owens Corning Canada | Foamular 604RB (Type 4) | ‒ | ‒ | 414 | 60 | 0.84 | 4.75 |
| Soprema Inc. | Sopra-XPS 35 | ‒ | ‒ | 350 | 51 | 0.88 | 5 |
| Soprema Inc. | Sopra-XPS 40, 60, 100 | ‒ | ‒ | 500, 600, 700 | 73, 87, 102 | 0.88 | 5 |
Expand
- EPS (Expanded Polystyrene Foam)
| Manufacturer | Product Name | System Test Type (Wind Uplift Resistance) | Compressive Strength (kPa) |
Compressive Strength (psi) |
Thermal Resistance (RSI/25.4 mm) @24°C (74°F) |
Thermal Resistance (R/inch) @24°C (74°F) |
|---|---|---|---|---|---|---|
| Airfoam Industries Ltd. | Korolite 100 (Type 1, Flat) | ‒ | 70 | 10 | 0.65 | 3.75 |
| Airfoam Industries Ltd. | Korolite 160 (Type 2, Flat) | ‒ | 110 | 16 | 0.7 | 4.04 |
| Airfoam Industries Ltd. | Korolite 250 (Type 3, Flat) | ‒ | 172 | 25 | 0.74 | 4.27 |
| Airfoam Industries Ltd. | Korolite 100 (Type 1, Tapered) | ‒ | 70 | 10 | 0.65 | 3.75 |
| Airfoam Industries Ltd. | Korolite 160 (Type 2, Tapered) | ‒ | 110 | 16 | 0.7 | 4.04 |
| Airfoam Industries Ltd. | Korolite 250 (Type 3, Tapered) | ‒ | 172 | 25 | 0.74 | 4.27 |
| Beaver Plasticts Ltd. | Terrafoam (Type 1, Flat) | ‒ | 70 | 10 | 0.65 | 3.75 |
| Beaver Plasticts Ltd. | Terrafoam (Type 2, Flat) | ‒ | 110 | 16 | 0.7 | 4.04 |
| Beaver Plasticts Ltd. | Terrafoam (Type 3, Flat) | ‒ | 140 | 20.4 | 0.74 | 4.27 |
| Beaver Plasticts Ltd. | Terrafoam (Type 1, Tapered) | ‒ | 70 | 10 | 0.65 | 3.75 |
| Beaver Plasticts Ltd. | Terrafoam (Type 2, Tapered) | ‒ | 110 | 16 | 0.7 | 4.04 |
| Beaver Plasticts Ltd. | Terrafoam (Type 3, Tapered) | ‒ | 140 | 20.4 | 0.74 | 4.27 |
| Plasti-Fab | Plastispan Insulation (Type 1) | ‒ | 70 | 10 | 0.65 | 3.75 |
| Plasti-Fab | Plastispan HD Insulation (Type 2) | ‒ | 110 | 16 | 0.7 | 4.04 |
| Plasti-Fab | Plastispan 25 Insulation (Type 3) | ‒ | 140 | 20 | 0.74 | 4.27 |
| Plasti-Fab | Plastispan Sloped Insulation | ‒ | ‒ | ‒ | ‒ | ‒ |
Expand
- Polyisocyanurate Foam
| Manufacturer | Product Name | System Test Type (Wind) | Density (kg/m3) | Compressive Strength (kPa) |
Compressive Strength (psi) |
Thermal Resistance (RSI/25.4 mm) |
Thermal Resistance (R/inch) |
|---|---|---|---|---|---|---|---|
| Atlas Roofing Corporation | AC Foam III | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| Atlas Roofing Corporation | AC Foam Supreme | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| Carlisle Syntec Systems Canada | SecurShield HD Plus | MARS PARS | ‒ | 138 | 20 | 1 | 5.7 |
| Carlisle Syntec Systems Canada | SecurShield RapidLock (RL) Polyiso | ‒ | ‒ | 138 | 20 | 1 | 5.7 |
| Carlisle Syntec Systems Canada | SecurShield RapidLock (RL) HD Polyiso | ‒ | ‒ | 138 | 20 | 1 | 5.7 |
| Elevate (fomerly Firestone) | ISOGARD CG | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| Hunter Panels | H-Shield CG | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| Hunter Panels | H-Shield Premier | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| Hunter Panels | H-Shield Composite | ‒ | 32 | 138 | 20 | 1 | 5.7 |
| IKO Industries Ltd. | IKOTherm III | ‒ | ‒ | 140 | 20 | 1 | 5.7 |
| Johns Manville Corporation | ENRGY 3 CGF Insulation | ‒ | ‒ | 138 | 20 | 1 | 5.7 |
| Polyglass USA, Inc. | Polytherm G | ‒ | 32.04 | 138 | 20 | 1 | 5.7 |
| Siplast, Inc. | Paratherm CG | ‒ | ‒ | 138 | 20 | 1 | 5.7 |
| Soprema Inc. | Sopra-Iso Plus | ‒ | 32 | 138 | 20 | 1 | 5.7 |
Expand
- Perlitic Insulation
| Manufacturer | Product Name | System Test Type (Wind) | Density (kg/cu. m) | Compressive Strength (kPa) | Compressive Strength (psi) | Thermal Resistance (RSI) | Thermal Resistance (R/inch) |
|---|---|---|---|---|---|---|---|
| Johns Manville Corporation | Fesco Board | ‒ | ‒ | ‒ | ‒ | 0.49 | 2.78 |
Expand
- Mineral Fibre Roof Insulation
| Manufacturer | Product Name | System Test Type (Wind) | Density (kg/cu. m) | Compressive Strength (kPa) |
Compressive Strength (psi) |
Thermal Resistance (RSI/25.4 mm) |
Thermal Resistance (R/inch) |
|---|---|---|---|---|---|---|---|
| ROCKWOOL | TOPROCK® DD | ‒ | See TDS | See TDS | See TDS | 0.62 | 3.5 |
| ROCKWOOL | TOPROCK® DD PLUS | ‒ | See TDS | See TDS | See TDS | 0.62 | 3.5 |
| ROCKWOOL | MULTIFIX TM | ‒ | See TDS | See TDS | See TDS | 0.68 | 3.8 |
| Soprema Inc. | Soprarock DD | ‒ | See TDS | See TDS | See TDS | 0.62 | 3.5 |
| Soprema Inc. | Soprarock DD PLUS | ‒ | See TDS | See TDS | See TDS | 0.62 | 3.5 |
| Soprema Inc. | Soprarock MD | ‒ | See TDS | See TDS | See TDS | See TDS | See TDS |
| Soprema Inc. | Soprarock MD Plus | ‒ | See TDS | See TDS | See TDS | See TDS | See TDS |
4 Insulation Overlay Boards
Expand
5 Eave and Detail Protection
Eave protection is used to protect the eave and valley areas of water-shedding roofs from ice dam damage. An ice dam usually forms when the interior heat of the building warms the snow on the roof, causing it to melt and run down to the eaves. Normally, eaves extend past the exterior face of the building and are not heated from the inside. This allows the water to freeze and form an ice dam. As the ice dam grows, it forms a barrier that prevents water from draining off the edge of the eaves. The water backs up behind the dam and gradually forces its way under the primary roof covering (asphalt shingles, metal panels, cedar shakes or shingles, etc.), where it warms and melts (the result of heat leakage through discontinuities in the air barrier system). Liquid water then leaks through the roof deck and into the structure. The results can range from minor staining to severe water damage to the structural members.
Eave protection membranes are designed to prevent the water from reaching the deck and leaking into the structure. These materials are self-adhering and manufactured with a rubberized asphaltic compound, or with butyl. Properly formulated and installed, these sheets have the potential to perform a long time. Slope and climate conditions are considerations for selection; refer to the Standard for further information and guidance.
Underlayment is used in the field areas of the roof (where eave protection is not required) to provide a secondary protection beneath the roof covering, during weather events that might force water underneath.
Notice to Reader
* Eave and Valley Protection - Some of the materials listed in the columns for eave or valley protection must be installed in multiple layers because, by themselves, they are too thin to satisfy the material requirements published in the Standard for Architectural Sheet Metal (ASM) Roof Systems. Consult the product manufacturer for appropriate application requirements, and the Standard for multiple layering requirements. If multi-layering is not permitted by the manufacturer, select a product with suitable thickness that may be applied in a single layer.
† Underlayment - While some materials listed as underlayments are nail-applied, their acceptability is dependent on roof slope. Refer to Part 8 in the Standard for Architectural Sheet Metal (ASM) Roof Systems before specifying or installing nail-applied materials; nail-applied underlayments are not permitted on slopes less than 1:3 (4" in 12").
| Manufacturer | Product Name | Product Type | Top Surface | Nominal Thickness mm (mil)* |
Application Method | Separation Layer |
Eaves & Valleys* |
Under- layment† |
|---|
| Click up/down arrows to sort | ||||||||
|---|---|---|---|---|---|---|---|---|
| Various | No. 30 Asphalt Felt | Felt underlayment | Non-woven Felt | ‒ | Nail-applied | X | X | ✔ |
| Building Products of Canada Corp. | Gripgard | SBS-modified Bituminous | ‒ | ‒ | Self-adhering | X | ✔ | ✔ |
| Building Products of Canada Corp. | Weathertex (SA) | SBS-modified Bituminous | Sanded | 1.50 (60) | Self-adhering | X | ✔ | ✔ |
| CertainTeed LLC | DiamondDeck | Polymeric | Synthetic Polymer | N/A | Nail-applied | ✔ | X | ✔ |
| CertainTeed LLC | RoofRunner AIR | Polymeric | Synthetic Polymer | 0.56 (22) | Nail-applied | ✔ | X | ✔ |
| CertainTeed LLC | WinterGuard Pro | SBS Modified Bituminous | Synthetic Polymer | 1.14 (45) | Self-adhering | ✔ | ✔ | ✔ |
| Elevate (fomerly Firestone) | Clad-Gard SA | SBS-modified Bituminous | Woven Polyethylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Elevate (fomerly Firestone) | Clad-Gard MA | SBS-modified Bituminous | ‒ | N/A | Self-adhering | X | ✔ | ✔ |
| FT Synthetics | PLATINUM | Polymeric | Polyolefin | 0.50 (20) | Nail-applied | ✔ | X | ✔ |
| FT Synthetics | SILVER | Polymeric | Polyolefin | 0.30 (12) | Nail-applied | ✔ | X | ✔ |
| FT Synthetics | PLATINUM HT-SA | Polymeric | GRIPSPOT TM | 1.04 (41) | Self-adhering | ✔ | ✔ | ✔ |
| FT Synthetics | Platinum HT-B | Polymeric | GRIPSPOT TM | 1.04 (41) | Self-adhering | ✔* | ✔ | ✔ |
| FT Synthetics | Cobalt Ultra | Polymeric | GRIPSPOT TM | 1.04 (41) | Self-adhering | ✔ | ✔ | ✔ |
| GAF Canada ULC | Stormguard | SBS-modified Bituminous | ‒ | 1.02 (40) | Self-adhering | X | ✔ | ✔ |
| GAF Canada ULC | Deck Armor | Polymeric | ‒ | ‒ | Nail-applied | ✔ | X | ✔ |
| GAF Canada ULC | FeltBuster | Polymeric | non-slip | ‒ | Nail-applied | ✔ | X | ✔ |
| Garland Canada Inc. | R-Mer Seal | Polymeric | Slip-resist. Polymer | 1.14 (45) | Self-adhering | ✔ | ✔ | ✔ |
| Garland Canada Inc. | Viking UDL Metal | Polymeric | Polyester | 1.52 (60) | Self-adhering | ✔ | ✔ | ✔ |
| HAL Industries Inc. | “Super” Tilemate G100 FW | SBS-modified Bituminous | Woven Polypropylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Henry Company Canada | Blueskin PE 200 HT | SBS-modified Bituminous | Polyethylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Henry Company Canada | Blueskin RF 200 | SBS-modified Bituminous | Slip-resistant Film | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Henry Company Canada | Eaveguard | SBS-modified Bituminous | Sanded | 1.30 (50) | Self-adhering | X | ✔ | ✔ |
| IKO Industries Ltd. | Stormshield Ice and Water Protector | SBS-modified Bituminous | Sanded | 1.08 (43) | Self-adhering | X | ✔ | ✔ |
| IKO Industries Ltd. | 44 Stormshield Ice and Water Protector | SBS-modified Bituminous | Sanded | 1.08 (43) | Self-adhering | X | ✔ | ✔ |
| IKO Industries Ltd. | Armourbond Flash Sand HD | SBS Modified Bituminous | Sanded | 3.00 (118) | Self-adhering | X | ✔ | ✔ |
| IKO Industries Ltd. | Armourgard Ice and Water Protector | SBS-modified Bituminous | Sanded | 1.40 (53) | Self-adhering | X | ✔ | ✔ |
| KPNE Products Ltd. | ULTRASeal SA HT | Polymeric/butyl | Slip-resist. polymer | 1.14 (45) | Self-adhering | X | ✔ | ✔ |
| Malarkey Roofing Products | Right Start™ UDL | SBS-modified Bituminous | Sanded | 1.40 (55) | Nail-applied | X | X | ✔ |
| Malarkey Roofing Products | Arctic Seal Ice & Water Guard | SBS-modified Bituminous | Sanded | 1.52 (60) | Self-adhering | X | X | ✔ |
| Malarkey Roofing Products | Secure Start Plus | Polymeric | Slip-resist. polymer | ‒ | Nail-applied | ✔ | X | ✔ |
| Malarkey Roofing Products | Secure Start SG | Polymeric | Smooth polymeric | ‒ | Nail-applied | ✔ | X | ✔ |
| Malarkey Roofing Products | Secure Start Permeable | Polymeric | Polymeric | ‒ | Nail-applied | ✔ | X | ✔ |
| Owens Corning Canada LP | Titanium UDL 25 | Polymeric | Synthetic (not stated) | 0.38 (15) | Nail-applied | ✔ | X | ✔ |
| Owens Corning Canada LP | Titanium UDL 30 | Polymeric | Synthetic (not stated) | 0.63 (25) | Nail-applied | ✔ | X | ✔ |
| Owens Corning Canada LP | Titanium UDL 50 | Polymeric | Synthetic (not stated) | 0.75 (30) | Nail-applied | ✔ | X | ✔ |
| Owens Corning Canada LP | Titanium PSU 30 | SBS-modified Bituminous | Synthetic Polymer | 1.10 (45) | Self-adhering | ✔ | ✔ | ✔ |
| Owens Corning Canada LP | RhinoRoof U20 | Polymeric | Not Stated | 0.18 (7) | Nail-applied | X | X | ✔ |
| Polyglass USA, Inc. | Polystick MTS | Proprietary Compound | Fibreglass mat | 1.50 (60) | Self-adhering | X | ✔ | ✔ |
| Protecto Wrap Company | Jiffy Seal Ice and Water Guard HT | SBS-modified Bituminous | Woven polyolefin | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Protecto Wrap Company | Jiffy Seal Butyl Ice and Water Guard HT | SBS-modified Bituminous | Woven polyolefin | 0.75 (30) | Self-adhering | ✔ | ✔ | ✔ |
| Sentry Building Innovations | Roofnado AnchorDeck | Polymeric | Not Stated | ‒ | Nail-applied | ✔ | X | ✔ |
| Sentry Building Innovations | Roofnado LapLock PSU (HT) | Polymeric/Self-adhered underside | Polymeric | ‒ | Self-adhering | ✔ | ✔ | ✔ |
| Sentry Building Innovations | StormTread XW | Polymeric | Not Stated | ‒ | Nail-applied | ✔ | X | ✔ |
| Sentry Building Innovations | Sahara (underlayment) | Polymeric | Not Stated | ‒ | Nail-applied | ✔ | X | ✔ |
| Sentry Building Innovations | Sahara AnchorDeck (underlayment) | Polymeric | Not Stated | ‒ | Nail-applied | ✔ | X | ✔ |
| Siplast | Paradiene 20 EG SA | SBS-modified Bituminous | Not Stated | 3.00 (118) | Self-adhering | X | ✔ | ✔ |
| Soprema Inc. | Lastobond 195 | SBS-modified Bituminous | Sanded | 1.60 (63) | Self-adhering | X | ✔ | ✔ |
| Soprema Inc. | Lastobond 240 | SBS-modified Bituminous | Sanded | 1.60 (63) | Self-adhering | X | ✔ | ✔ |
| Soprema Inc. | Lastobond Shield | SBS-modified Bituminous | Woven polyethylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Soprema Inc. | Lastobond Shield HT | SBS-modified Bituminous | Woven polyethylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Soprema Inc. | Sopraseal Stick 1100 T | SBS-modified Bituminous | Woven polyethylene | 1.00 (40) | Self-adhering | ✔ | ✔ | ✔ |
| Soprema Inc. | Sopraply Stick Duo | SBS-modified Bituminous | Sanded | 3.00 (120) | Self-adhering | X | ✔ | ✔ |
| Soprema Inc. | Lastobond Stick VP | SBS-modified Bituminous | Trilaminar polypropylene | 0.60 (24) | Self-adhering | ✔ | X | ✔ |
| VaproShield LLC | SlopeShield Plus Self-Adhered | Polymeric | Trilaminar polypropylene | 0.51 (20) | Self-adhering | ✔ | X | ✔ |
6 Standing Seam Metal Roof System - Job Site Roll-forming
- All architectural metal roofing accepted for application in the RoofStar Guarantee Program utilizes a locking standing seam. There are three seam types currently offered with site-formed metal roofing systems (click on a type to see an illustration). Refer to the table below for a summary of panel manufacturers and the products they supply:
Expand
- Note that not all panels are made with stiffener ribs. Refer to each manufacturer's literature by clicking on the product name in the table.
7 Proprietary Metal Roof Systems (Manufactured in Plant Roll-forming)
Expand
- RoofStar-accepted proprietary standing seam metal roof systems, installed in conformance with RoofStar Guarantee Standards, qualify for a five (5) or ten (10) year guarantee under the RoofStar Guarantee Program.