Difference between revisions of "Materials:(Bothwell-Accurate) BA-Versaspan 100 (SS 100)"
Difference between revisions of "Materials:(Bothwell-Accurate) BA-Versaspan 100 (SS 100)"
(→PERFORMANCE REQUIREMENTS) |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 26: | Line 26: | ||
====OVERVIEW==== | ====OVERVIEW==== | ||
| − | The BA- | + | The BA-Versaspan 100 (SS 100) standing seam panel is formed with an on-site/in-shop continuous metal roofing panel roll forming machine (New Tech SS Multipro). This machine produces a standing seam panel with a seam height of 25.4 mm (1") and profiles can vary from 330.2 mm (13") wide up to 533.4 mm (21") wide. This machine also produces FF 100 (BA-Versasnap), SS 675 (BA-Versaclip), SS 150 (BA-Versaspan 150). |
On-site roll forming provides for the elimination of end laps with continuous panel forming capabilities in lengths up to 200' plus (depending on coil size and handling/maneuvering. | On-site roll forming provides for the elimination of end laps with continuous panel forming capabilities in lengths up to 200' plus (depending on coil size and handling/maneuvering. | ||
====SYSTEM DESCRIPTION==== | ====SYSTEM DESCRIPTION==== | ||
| − | #'''General''': The BA- | + | #'''General''': The BA-Versaspan 100 (SS 100) is a standing seam concealed fastener roof panel. The panel is attached with clips to allow for expansion and contraction. The maximum spacing of the clips and fasteners are 76.2mm (3'). |
#'''Range of application''': Installed on wood or steel sloped roofs, in commercial, institutional, industrial and residential construction. For re-roofing or new construction. Considered a traditional standing seam panel. | #'''Range of application''': Installed on wood or steel sloped roofs, in commercial, institutional, industrial and residential construction. For re-roofing or new construction. Considered a traditional standing seam panel. | ||
#'''Fasteners (Screws)''': Fasteners used to attach panel clips to plywood to be No. 10-12 by 25 mm (1") long pancake head, No. 2 Phillips drive, A-point, coated steel screw. Minimum two fasteners per clip to be used. | #'''Fasteners (Screws)''': Fasteners used to attach panel clips to plywood to be No. 10-12 by 25 mm (1") long pancake head, No. 2 Phillips drive, A-point, coated steel screw. Minimum two fasteners per clip to be used. | ||
| Line 56: | Line 56: | ||
====PERFORMANCE REQUIREMENTS==== | ====PERFORMANCE REQUIREMENTS==== | ||
| − | + | <ol> | |
| − | + | <li>'''Wind Uplift Resistance''': Panel securement shall conform to the requirements in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#PART_3 Part 3] of the [http://rpm.rcabc.org/index.php?title=Standard_for_Architectural_Sheet_Metal_(ASM)_Systems Standard for Architectural Sheet Metal (ASM) Systems]. | |
| + | <li>'''Materials''':RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#Section_9.2._Materials Section 9.2.] of the Standard. | ||
| + | </li></ol> | ||
<hr> | <hr> | ||
Latest revision as of 17:07, 26 October 2023
Division C - Accepted Materials
BA Versaspan 100 (SS 100)
by Bothwell-Accurate Company (B.C.) Ltd.
| The metal panel listed and described below is accepted for use in the RoofStar Guarantee Program. |
The roofing assembly / material information published below and in the RCABC Roofing Practices Manual DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority. For more information about this product or system, consult the manufacturer. |
OVERVIEW
The BA-Versaspan 100 (SS 100) standing seam panel is formed with an on-site/in-shop continuous metal roofing panel roll forming machine (New Tech SS Multipro). This machine produces a standing seam panel with a seam height of 25.4 mm (1") and profiles can vary from 330.2 mm (13") wide up to 533.4 mm (21") wide. This machine also produces FF 100 (BA-Versasnap), SS 675 (BA-Versaclip), SS 150 (BA-Versaspan 150).
On-site roll forming provides for the elimination of end laps with continuous panel forming capabilities in lengths up to 200' plus (depending on coil size and handling/maneuvering.
SYSTEM DESCRIPTION
- General: The BA-Versaspan 100 (SS 100) is a standing seam concealed fastener roof panel. The panel is attached with clips to allow for expansion and contraction. The maximum spacing of the clips and fasteners are 76.2mm (3').
- Range of application: Installed on wood or steel sloped roofs, in commercial, institutional, industrial and residential construction. For re-roofing or new construction. Considered a traditional standing seam panel.
- Fasteners (Screws): Fasteners used to attach panel clips to plywood to be No. 10-12 by 25 mm (1") long pancake head, No. 2 Phillips drive, A-point, coated steel screw. Minimum two fasteners per clip to be used.
- Roof Deck Fasteners (Panel Clips): One piece assembly 43.75 mm (1-3/4") wide, 31 mm (1-1/4") high. Minimum thickness 0.022 in. (No. 22 MSG). Clips spaced maximum 900 mm (36") O.C., fastened to plywood deck.
- Deck Requirements: in keeping with the Standard for Architectural Sheet Metal (ASM) Systems.
PROFILE
| BA-Versaspan 100 (SS 100) Standing Seam Panel |
|---|
|
TECHNICAL DATA SHEET
Click below for the Technical Data Sheet
SITE CONDITIONS
Minimum roof slope is 1:12 (1" in 12"). Severe conditions (heavy snow or ice) minimum slope is 1:4 (3" in 12").
PERFORMANCE REQUIREMENTS
- Wind Uplift Resistance: Panel securement shall conform to the requirements in Part 3 of the Standard for Architectural Sheet Metal (ASM) Systems.
- Materials:RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in Section 9.2. of the Standard.