Difference between revisions of "Materials:(Cascade) Zimmerman SS1500"

Latest revision as of 17:08, 26 October 2023

Division C - Accepted Materials

Zimmerman SS1500
by Cascade Roofing & Exteriors Inc.

The metal panel listed and described below is accepted for use in the RoofStar Guarantee Program.

Manufacturer Cascade Roofing & Exteriors Inc. Contact Address See the current Membership list and contact information at www.rcabc.org Product Group - Standing Seam Metal Roof System Panel Machine Zimmerman Panel Name Zimmerman SS 1500 Seam Type Mechanical Lock The roofing assembly / material information published below and in the RCABC Roofing Practices Manual DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority. For more information about this product or system, consult the manufacturer.

OVERVIEW

The Zimmerman SS 1500 is an on-site continuous panel metal roofing machine. Panel profiles vary from 300 mm (12") to 500 mm (20") wide with a standing seam height of 38 mm (1½").

This on–site manufacturing eliminates the need for end laps, with continuous panel forming capabilities in lengths up to 15 – 24 m (50’).

SYSTEM DESCRIPTION

General: Standing seam panels employ a hidden fastening system for securement to a solid substrate. The maximum spacing of the clips is 600 mm (24") on centre. The panels are locked together, with the clips as part of the seam, by use of a mechanical seamer.
Range of application: on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction. Plywood decking is to be nominal 13mm (½") thick or thicker.
Fasteners (Screws): To attach clips to plywood, use #8 x 1" long pancake head, A-point, coated steel screw. Minimum 2 screws per clip. For steel decking or Z-girts, use #8 x 1" long pancake head, having a self-drill and tap point, minimum 2 screws per clip.
Panel Clips: One-piece clip 64 mm (2½") wide by 38mm (1½") high with a 16 mm (5/8") base. The minimum thickness is 22 gauge metal; fastened to a plywood deck 600 mm (24") O.C. Custom-Built 2SS RC1.5" standing seam roof clip.
Deck Requirements: in keeping with the Standard for Architectural Sheet Metal (ASM) Systems.

PROFILE

N/A

TECHNICAL DATA SHEET

N/A

SITE CONDITIONS

Minimum roof slope is 1:4 (3" in 12"). Severe conditions (heavy snow or ice) minimum slope is 1:1.5 (8" in 12").

PERFORMANCE REQUIREMENTS

Wind Uplift Resistance: Panel securement shall conform to the requirements in Part 3 of the Standard for Architectural Sheet Metal (ASM) Systems.
Materials:RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in Section 9.2. of the Standard.

Back to Site-Formed Metal Roofing Systems

Back to Accepted Materials

Home

@@ Line 1: / Line 1: @@
-Manufacturer: <b>CASCADE ROOFING & WATERPROOFING (2007) INC.</b>
+__NOTOC__
+__NONUMBEREDHEADINGS__
+{{DISPLAYTITLE:<span style="position: absolute; clip: rect(1px 1px 1px 1px); clip: rect(1px, 1px, 1px, 1px);">{{FULLPAGENAME}}</span>}}
-Contact Address: See the current Membership list and contact information at [http://www.rcabc.org/members/find-a-member/ '''www.rcabc.org''']
+<big><big>Division C - Accepted Materials</big></big>
+<hr>
+<big><big><big><big><big>Zimmerman SS1500</big></big></big></big></big><br>
+<big><big><big>by Cascade Roofing & Exteriors Inc.</big></big></big><br>
+{| class="wikitable"
+|-
+| style="background-color: #ffffcc; column-width:100%" | The metal panel listed and described below is accepted for use in the '''''RoofStar Guarantee Program'''''.
+|}
+{| class="wikitable"
+|-
+|
+;'''Manufacturer''': Cascade Roofing & Exteriors Inc.
+;'''Contact Address''': See the current Membership list and contact information at [http://www.rcabc.org/members/find-a-member/ www.rcabc.org]
+;'''Product Group - Standing Seam Metal Roof System'''
+;'''Panel Machine''': Zimmerman
+;'''Panel Name''': Zimmerman SS 1500
+;'''Seam Type''': Mechanical Lock
-Product Group: <b>STANDING SEAM METAL ROOF SYSTEM ZIMMERMAN SS 1500 STANDING SEAM PANEL</b>
+The roofing assembly / material information published below and in the [http://{{SERVERNAME}}/index.php?title=Main_Page RCABC Roofing Practices Manual] DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.  For more information about this product or system, consult the manufacturer.
+|}
-;DESCRIPTION
+====OVERVIEW====
+The Zimmerman SS 1500 is an on-site continuous panel metal roofing machine. Panel profiles vary from 300 mm (12") to 500 mm (20") wide with a standing seam height of 38 mm (1&#189;").
-:The Zimmerman SS 1500 is an on-site continuous panel metal roofing machine. Panel profiles vary from 300 mm (12") to 500 mm (20") wide with a standing seam height of 38 mm (1&#189;").
+This on&#8211;site manufacturing eliminates the need for end laps, with continuous panel forming capabilities in lengths up to 15 &#8211; 24 m (50&#8217;).
-:This on&#8211;site manufacturing eliminates the need for end laps, with continuous panel forming capabilities in lengths up to 15 &#8211; 24 m (50&#8217;).
+====SYSTEM DESCRIPTION====
+#'''General''': Standing seam panels employ a hidden fastening system for securement to a solid substrate. The maximum spacing of the clips is 600 mm (24") on centre.  The panels are locked together, with the clips as part of the seam, by use of a mechanical seamer.
+#'''Range of application''': on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction. Plywood decking is to be nominal 13mm (&#189;") thick or thicker.
+#'''Fasteners (Screws)''': To attach clips to plywood, use #8 x 1" long pancake head, A-point, coated steel screw. Minimum 2 screws per clip. For steel decking or Z-girts, use #8 x 1" long pancake head, having a self-drill and tap point, minimum 2 screws per clip.
+#'''Panel Clips''': One-piece clip 64 mm (2&#189;") wide by 38mm (1&#189;") high with a 16 mm (5/8") base. The minimum thickness is 22 gauge metal; fastened to a plywood deck 600 mm (24") O.C. Custom-Built 2SS RC1.5" standing seam roof clip.
+#'''Deck Requirements''': in keeping with the [http://rpm.rcabc.org/index.php?title=Standard_for_Architectural_Sheet_Metal_(ASM)_Systems Standard for Architectural Sheet Metal (ASM) Systems].
-.1 <u>GENERAL</u>
+====PROFILE====
+N/A
-:The roofing assembly / material information published in the <b>RCABC <i>Roofing Practices Manual</i></b> DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority.
+====TECHNICAL DATA SHEET====
+N/A
-.2 <u>SYSTEM DESCRIPTION</u>
+====SITE CONDITIONS====
+Minimum roof slope is 1:4 (3" in 12"). Severe conditions (heavy snow or ice) minimum slope is 1:1.5 (8" in 12").
-:.1 Standing seam panels employ a hidden fastening system for securement to a solid substrate. The maximum spacing of the clips is 600 mm (24") on centre.  The panels are locked together, with the clips as part of the seam, by use of a mechanical seamer.
+====PERFORMANCE REQUIREMENTS====
+<ol>
-:.2 Range of application for this panel: on wood or metal-sloped roofs; in commercial, institutional, industrial and residential construction; for reroofing or new construction.
+<li>'''Wind Uplift Resistance''': Panel securement shall conform to the requirements in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#PART_3 Part 3] of the [http://rpm.rcabc.org/index.php?title=Standard_for_Architectural_Sheet_Metal_(ASM)_Systems Standard for Architectural Sheet Metal (ASM) Systems].
+<li>'''Materials''':RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in [https://rpm.rcabc.org/index.php?title=ASM_Roof_Systems_Standard#Section_9.2._Materials Section 9.2.] of the Standard.
-:.3 <b>Panel Attachment:</b>
+</li></ol>
-:;Panel clips
-::One piece clip 64 mm (2&#189;") wide by 38mm (1&#189;") high with a 16 mm (5/8") base. The minimum thickness is 22 gauge metal; fastened to a plywood deck 600 mm (24") on centre. Custom-Built 2SS RC1.5" standing seam roof clip.
-:;Fasteners
-::Used to attach clips to plywood to be #8 x 1" long pancake head, A-point, coated steel screw. Minimum 2 screws per clip. For steel decking or Z-girts, #8 x 1" long pancake head, having a self-drill and tap point, minimum 2 screws per clip.
-:.4 Plywood decking is to be nominal 13mm (&#189;") thick or thicker.
-.3 <u>SITE CONDITIONS</u>
-:.1 Minimum roof slope is 1:6 (2" in 12"). Severe conditions (heavy snow or ice) minimum slope is 1:1.5 (8" in 12").
-;1.4 <u>PERFORMANCE REQUIREMENTS</u>
-:#'''Wind Uplift Standards''': Engineered designs to resist wind uplift may refer to the British Columbia Building Code, Div. B, Appendix C, Table C-2 which lists various types of loads, including wind loads, for specific reference locations throughout the province. See also [http://{{SERVERNAME}}/index.php?title=ASM_Application_Guides_and_Notes Guides and Notes (Wind Resistance)] for a simplified calculation procedure. Regardless of the resources indicated here, the Design Authority is responsible to perform accurate wind load calculations and specify securement requirements.
-:#'''Materials''':RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the standards published in the [http://rpm.rcabc.org/index.php/RoofStar_Guarantee_Standards_for_ASM_Roof_Assemblies Architectural Sheet Metal (ASM) Roof Standards].
 <hr>