Materials:(Lam) SS 150 Standing Seam (38 mm)

Division C - Accepted Materials

SS 150 Standing Seam
by Lam Metal Contracting Ltd.

Material Acceptance and Product Details The information published in the RCABC Roofing Practices Manual and offered below does NOT represent a complete set of the manufacturer’s data or specifications, nor is this material recommended or endorsed by the Guarantor. The preparation of a detailed specification is the responsibility of the Design Authority.
Manufacturer Lam Metal Contracting Ltd. Contact Address See the current Membership list and contact information at www.rcabc.org Product Group - Standing Seam Metal Roof System Panel Machine Nu-Tech Panel Name SS 150 Seam Type Mechanical Lock The roofing assembly / material information published below and in the RCABC Roofing Practices Manual DOES NOT represent a complete set of the manufacturer's published data, nor does it represent a detailed specification. The preparation of a detailed specification is the responsibility of the design authority. For more information about this product or system, consult the manufacturer.

OVERVIEW

The SS 150 standing seam panel is formed in-house with an Nu-Tech SSP continuous metal roofing panel roll forming machine. This machine produces a standing seam panel with a seam height of 38.1 mm (1-1/2"). Profiles can vary from 304.8 mm (12") wide to 609.6 mm (24") wide.

This machine also produces the Nu-Tech SS200 panel profile and a 44 mm (1-3/4") high Nu-Tech panel profile.

SYSTEM DESCRIPTION

General: The SS 150 panel is a standing seam concealed fastener roofing panel. The maximum spacing of the clips is 609.6 mm (24") O.C.
Range of application: on wood or metal sloped roofs; in commercial, institutional, industrial and residential construction; for re-roofing or new construction.
Fasteners (Screws):
1. Fasteners (screws) used to attach panels to plywood deck to be No. 10-12 by 19.05 mm (5/8") long pancake head wood screw. Minimum two fasteners per clip to be used.
2. Two-piece assembly consists of a steel base approximately 127 mm (5") wide x 25.4 mm (1") long, with a minimum thickness of 0.026 (No. 24 MSG) and an upper tab that measures 50.8 mm high with a minimum thickness of 0.020 (No. 26 MSG). One panel clip spaced at 609.6 mm (24") O.C. maximum.
Fabrication: Unless otherwise shown on drawings or specified herein, fabricate panels in continuous one piece lengths and fabricate flashings and accessories in longest practical lengths.
Deck Requirements: in keeping with the Standard for Architectural Sheet Metal (ASM) Systems.

PROFILE

SS 150 Standing Seam Panel

DELIVERY, STORAGE & HANDLING

Protect against damage and discoloration.
Handle panels with non-marring slings.
Do not bend panels.
Store panels above ground, with one end elevated for drainage.
Protect panels against standing water and condensation between adjacent surfaces.
If panels become wet, immediately separate sheets, wipe dry with clean cloth, allow to air dry.

FIELD MEASUREMENTS

Verify prior to fabrication.
If field measurements differ from drawing dimensions, notify Architect / Professional Engineer prior to fabrication.

PROTECTION

Treat, or isolate with protective material, any contacting surfaces of dissimilar materials to prevent electrolytic corrosion.

PROFILE

N/A

TECHNICAL DATA SHEET

N/A

SITE CONDITIONS

Minimum roof slope is 1:6 (2" in 12").
Verify that structural deck to receive panels is complete, in true plane, secure and otherwise properly prepared.
Prior to starting work, notify General Contractor about defects requiring correction.
Do not start work until conditions are satisfactory.

PERFORMANCE REQUIREMENTS

Wind Uplift Resistance: Panel securement shall conform to the requirements in Part 3 of the Standard for Architectural Sheet Metal (ASM) Systems.
Materials:RoofStar (RGC) accepted metal panel systems shall be formed of steel conforming to the requirements published in Section 9.2. of the Standard.

Back to Site-Formed Metal Roofing Systems

Back to Accepted Materials

Home