Roofs - Insulation (Waterproofing Systems)

Jump to: navigation, search

Roofs - Insulation (Waterproofing Systems)


Division C - Accepted Materials


Roofs: Insulation

Accepted Materials for a RoofStar Guarantee

The tables and products shown below provide basic material data and links to more information about the materials, including manufacturers' published Technical Data sheets, but this information is not intended for use as a comparison of material performance or quality. It is the sole responsibility of the Design Authority to assess the performance capability and material suitability for specific design requirements.

The materials listed are those which have been accepted by the RoofStar Guarantee Program (RCABC Guarantee Corp., or RGC) for use in a roof or grade-level waterproofing system that will qualify for a RoofStar Guarantee. The acceptance of these materials by the RGC (RoofStar Guarantee Program) in no way reflects on the quality or performance of other materials not listed.

The materials and guideline specifications are listed under the name of the manufacturer and/or supplier of the primary membrane material, with the exception of BUR membranes for which the reader will find RoofStar Guarantee Program guidelines on traditional built-up roofing systems (BUR) incorporating organic and glass felt primary membranes.

1 Heat-resistant Insulation

Polyisocyanurate Foam
"Polyiso" Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program. NOTE: materials linked to Tested Assembly tables may be displayed separately or located only in Tested Assembly reports.
Manufacturer Product Name System Test Type (Wind) Density (kg/m3) Compressive
Strength
(kPa)
Compressive
Strength
(psi)
Thermal
Resistance
(RSI/25.4 mm)
Thermal
Resistance
(R/inch)
Atlas Roofing Corporation AC Foam III 32 138 20 1 5.7
Atlas Roofing Corporation AC Foam Supreme 32 138 20 1 5.7
Carlisle Syntec Systems Canada SecurShield HD Plus MARS PARS 138 20 1 5.7
Carlisle Syntec Systems Canada SecurShield RapidLock (RL) Polyiso 138 20 1 5.7
Carlisle Syntec Systems Canada SecurShield RapidLock (RL) HD Polyiso 138 20 1 5.7
Elevate (fomerly Firestone) ISOGARD CG 32 138 20 1 5.7
Hunter Panels H-Shield CG 32 138 20 1 5.7
Hunter Panels H-Shield Premier 32 138 20 1 5.7
Hunter Panels H-Shield Composite 32 138 20 1 5.7
IKO Industries Ltd. IKOTherm III 140 20 1 5.7
Johns Manville Corporation ENRGY 3 CGF Insulation 138 20 1 5.7
Polyglass USA, Inc. Polytherm G 32.04 138 20 1 5.7
Siplast, Inc. Paratherm CG 138 20 1 5.7
Soprema Inc. Sopra-Iso Plus 32 138 20 1 5.7
Mineral Fibre Roof Insulation
Mineral Fibre Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program. NOTE: materials linked to Tested Assembly tables may be displayed separately or located only in Tested Assembly reports.
Manufacturer Product Name System Test Type (Wind) Density (kg/cu. m) Compressive
Strength
(kPa)
Compressive
Strength
(psi)
Thermal
Resistance
(RSI/25.4 mm)
Thermal
Resistance
(R/inch)
ROCKWOOL TOPROCK® DD See TDS See TDS See TDS 0.62 3.5
ROCKWOOL TOPROCK® DD PLUS See TDS See TDS See TDS 0.62 3.5
ROCKWOOL MULTIFIX TM See TDS See TDS See TDS 0.68 3.8
Soprema Inc. Soprarock DD See TDS See TDS See TDS 0.62 3.5
Soprema Inc. Soprarock DD PLUS See TDS See TDS See TDS 0.62 3.5
Soprema Inc. Soprarock MD See TDS See TDS See TDS See TDS See TDS
Soprema Inc. Soprarock MD Plus See TDS See TDS See TDS See TDS See TDS
Composite Board Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program
Manufacturer Product Name System Test Type (Wind) Density (kg/cu. m) Compressive Strength (kPa/25.4 mm) Compressive Strength (psi/1 in. thick) Thermal Resistance (RSI/25.4 mm) Thermal Resistance (R/inch)
Posi-Slope Western MF (Protect Board Composite)
Soprema Inc. Xpress Board HD 200 190 (at 25%) 28 (at 25%) 0.70 K/W 4
Soprema Inc. Xpress ISO 138 (Polyiso only) 20 (Polyiso only) 1.0 5.7
Perlitic Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program
Manufacturer Product Name System Test Type (Wind) Density (kg/cu. m) Compressive Strength (kPa) Compressive Strength (psi) Thermal Resistance (RSI) Thermal Resistance (R/inch)
Johns Manville Corporation Fesco Board 0.49 2.78
Lightweight Insulating Concrete
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program
Manufacturer Product Name System Test Type (Wind) Density (kg/cu. m) Compressive Strength (kPa) Compressive Strength (psi) Thermal Resistance (RSI) Thermal Resistance (R/inch)
Siplast NVS Concrete 560 2070 300 N/A N/A
Siplast INSULCEL Concrete 480 1380 200 N/A N/A

2 Heat-sensitive Insulation

Because of their nature, heat-sensitive insulation materials need to be protected from temperatures exceeding the published service temperature (the maximum specified in-service in-service temperature for the material, above which the product may suffer distortion and reduced thermal performance). Thus, the Design Authority must refer to the applicable RoofStar Guarantee Standards for the roof system and review the requirements for suitable overlays, when applicable.

XPS (Extruded Polystyrene Foam)
XPS Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program. NOTE: materials linked to Tested Assembly tables may be displayed separately or located only in Tested Assembly reports.
Manufacturer Product Name System Test Type (Wind) Density (kg/cu. m) Compressive
Strength
(kPa)
Compressive
Strength
(psi)
Thermal
Resistance
(RSI/25.4 mm)
Thermal
Resistance
(R/inch)
Dupont Specialty Products Division - Safety and Construction Deckmate (Type 2) 110 16 0.87 5
Dupont Specialty Products Division - Safety and Construction Deckmate Plus (Type 3) 140 20 0.87 5
Dupont Specialty Products Division - Safety and Construction Roofmate (Type 4) 240 35 0.87 5
Dupont Specialty Products Division - Safety and Construction Roofmate CT (Type 4) 240* 35* 0.87 5
Owens Corning Canada Foamular C200 (Type 3) 140 20 0.88 5
Owens Corning Canada Foamular F350 (Type 4) 240 35 0.88 5
Owens Corning Canada Foamular 400 (Type 4) 275 40 0.88 5
Owens Corning Canada Foamular 600 (Type 4) 415 60 0.88 5
Owens Corning Canada Foamular 1000 (Type 4) 690 100 0.88 5
Owens Corning Canada Foamular 404 (Type 4) 276 40 0.88 5
Owens Corning Canada Foamular 604 (Type 4) 414 60 0.88 5
Owens Corning Canada Foamular 404RB (Type 4) 276 40 0.84 4.75
Owens Corning Canada Foamular 604RB (Type 4) 414 60 0.84 4.75
Soprema Inc. Sopra-XPS 35 350 51 0.88 5
Soprema Inc. Sopra-XPS 40, 60, 100 500, 600, 700 73, 87, 102 0.88 5
EPS (Expanded Polystyrene Foam)
EPS Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program. NOTE: materials linked to Tested Assembly tables may be displayed separately or located only in Tested Assembly reports.
Manufacturer Product Name System Test Type (Wind Uplift Resistance) Compressive
Strength
(kPa)
Compressive
Strength
(psi)
Thermal
Resistance
(RSI/25.4 mm)
@24°C (74°F)
Thermal
Resistance
(R/inch)
@24°C (74°F)
Airfoam Industries Ltd. Korolite 100 (Type 1, Flat) 70 10 0.65 3.75
Airfoam Industries Ltd. Korolite 160 (Type 2, Flat) 110 16 0.7 4.04
Airfoam Industries Ltd. Korolite 250 (Type 3, Flat) 172 25 0.74 4.27
Airfoam Industries Ltd. Korolite 100 (Type 1, Tapered) 70 10 0.65 3.75
Airfoam Industries Ltd. Korolite 160 (Type 2, Tapered) 110 16 0.7 4.04
Airfoam Industries Ltd. Korolite 250 (Type 3, Tapered) 172 25 0.74 4.27
Beaver Plasticts Ltd. Terrafoam (Type 1, Flat) 70 10 0.65 3.75
Beaver Plasticts Ltd. Terrafoam (Type 2, Flat) 110 16 0.7 4.04
Beaver Plasticts Ltd. Terrafoam (Type 3, Flat) 140 20.4 0.74 4.27
Beaver Plasticts Ltd. Terrafoam (Type 1, Tapered) 70 10 0.65 3.75
Beaver Plasticts Ltd. Terrafoam (Type 2, Tapered) 110 16 0.7 4.04
Beaver Plasticts Ltd. Terrafoam (Type 3, Tapered) 140 20.4 0.74 4.27
Plasti-Fab Plastispan Insulation (Type 1) 70 10 0.65 3.75
Plasti-Fab Plastispan HD Insulation (Type 2) 110 16 0.7 4.04
Plasti-Fab Plastispan 25 Insulation (Type 3) 140 20 0.74 4.27
Plasti-Fab Plastispan Sloped Insulation

3 BUR and Hot-mopped Applications only

Fibreboard Roof Insulation
Click on a manufacturer's name to see the full list of their products accepted for use in the RoofStar Guarantee Program
Manufacturer Product Name System Test Type (Wind) Description Density (kg/cu. m) Compressive Strength (kPa) Compressive Strength (psi) Thermal Resistance (RSI) Thermal Resistance (R/inch)
IKO Industries Ltd. Asphalt Fibreboard Impregnated/Coated
MSL Petroleum Paraffin Natural Natural Fibreboard
MSL Petroleum Paraffin HD High Density Fibreboard
MSL Asphalt Coated (6 sides) Asphalt Coated - 6 sides (Natural Fibreboard)
MSL Asphalt and Wax Impregnated Fibreboard Asphalt and Wax-impregnated
MSL Asphalt and Wax Impregnated HD Asphalt and Wax-impregnated HD
MSL Securpan Fire-resistant fibreboard
MSL Securpan (asphalt coated) Asphalt-coated on 1 side / fire-resistant

Accepted Materials

Home

© RCABC 2024
RoofStarTM is a registered Trademark of the RCABC.
No reproduction of this material, in whole or in part, is lawful without the expressed permission of the RCABC Guarantee Corp.